Brother HL-2132

1. The machine is in Deep Sleep mode (reducing more power consumption than Sleep mode).
2. The machine acts as though it were turned off.
3. If the machine does not receive data for a certain length of time while it is in Sleep mode, it enters Deep Sleep mode automatically.
4. Receiving data or pressing Go wakes up the machine from Deep Sleep mode to Ready mode.

1. The control panel has Toner, Drum, Error and Ready LEDs and the Go button.
2. Toner indicates low toner; Drum indicates a drum nearing replacement; Error indicates no paper, a paper jam or an open cover; Ready flashes according to machine status.
3. Go supports wake-up, error recovery, form feed, job cancellation and reprinting.
4. Wireless switching applies only to HL-2135W and HL-2270DW.

1. First, check the following: The AC power cord is connected properly and the machine is turned on.
2. All of the protective parts have been removed.
3. The toner cartridge and drum unit is installed properly.
4. The front cover, back cover, and fuser cover are completely closed.
5. Paper is inserted properly in the paper tray.
6. The interface cable is securely connected to the machine and the computer.
7. The correct driver for the machine has been chosen and is installed.
8. The computer is set up to connect to the correct machine port.
9. Machine does not print:

1. If you have a print quality problem, print a test page first (see Print a test page on page 61).
2. If the printout looks good, the problem is probably not the machine.
3. Check the interface cable or try the machine on another computer.
4. Brother does not recommend the use of cartridges other than genuine Brother Original cartridges or the refilling of used cartridges with toner from other sources.

1. Before buying large quantities, test a small amount.
2. Use paper made for plain-paper copying.
3. Tray 1 accepts plain, recycled and thin paper; the manual feed slot also accepts bond, thick paper, labels and envelopes.
4. Do not mix paper types or sizes in the tray.
5. Match the application paper size to the loaded paper.
6. Avoid touching the printed surface immediately.
7. The manual recommends neutral long-grain copy paper of 75–90 g/m² with approximately 5% moisture.
8. Tray 1 holds up to 250 sheets of 80 g/m² paper; manual feed holds one sheet.
9. Tray sizes: A4, Letter, B5 (ISO/JIS), A5, A5 long edge, B6 (ISO), A6 and Executive.
10. Manual-feed width is 76.2–216 mm and length is 116–406.4 mm.
11. Plain paper is 75–105 g/m², thin paper 60–75 g/m²; bond and thick paper up to 163 g/m² must use the manual feed slot.

1. Types of paper to avoid IMPORTANT Some types of paper may not perform well or may cause damage to your machine.
2. DO NOT use paper: that is highly textured that is extremely smooth or shiny that is curled or warped 1 A curl of 2 mm (0.08 in.) or greater may cause jams to occur. that is coated or has a chemical finish that is damaged, creased or folded that exceeds the recommended weight specification in this guide with tabs and staples with letterheads using low temperature dyes or thermography that is multipart or carbonless that is designed for inkjet printing If you use any of the types of paper listed above, they may damage your machine.
3. This damage is not covered under any Brother warranty or service agreement.

1. Envelopes Most envelopes designed for laser printers will be suitable for your machine.
2. However, some envelopes may have feed and print-quality problems because of the way they have been made.
3. A suitable envelope should have edges with straight, well-creased folds and the leading edge should not be thicker than two sheets of paper.
4. The envelope should lie flat and not be of baggy or flimsy construction.
5. You should buy quality envelopes from a supplier who understands that you will be using the envelopes in a laser machine.
6. We recommend that you print a test envelope to make sure the print results are what you want.
7. Types of envelopes to avoid IMPORTANT DO NOT use envelopes: that are damaged, curled, wrinkled, irregularly shaped, extremely shiny or textured envelopes. with clasps, staples, snaps, tie strings, self-adhesive components, windows, holes, cutouts or perforations. that are of a baggy construction, not sharply creased, embossed (have raised writing on them) or preprinted on the inside. that were previously printed by a laser / LED printer. that cannot be arranged when put in a pile. that are made of paper that weighs more than the paper weight specifications for the machine. with edges that are not straight or consistently square. with glue on surface as shown in figure below with double flaps as shown in figure below with sealing flaps that are not folded down when purchased with sealing flaps as shown in figure below with each side folded as shown in figure below If you use any of the types of envelopes listed above, they may damage your machine.
8. This damage may not be covered under any Brother warranty or service agreement.

1. Labels The machine will print on most types of labels designed for use with a laser printer.
2. Labels should have an adhesive that is acrylic-based since this material is more stable at the high temperatures in the fuser unit.
3. Adhesives should not come in contact with any part of the machine, because the label stock may stick to the drum unit or rollers and cause jams and print quality problems.
4. No adhesive should be exposed between the labels.
5. Labels should be arranged so that they cover the entire length and width of the sheet.
6. Using labels with spaces may result in labels peeling off and causing serious jams or print problems.
7. All labels used in this machine must be able to withstand a temperature of 200 degrees centigrade (392 degrees Fahrenheit) for a period of 0.1 seconds.
8. Do not feed a label sheet through the machine more than one time.
9. Types of labels to avoid Do not use labels that are damaged, curled, wrinkled or an unusual shape.
10. IMPORTANT Avoid feeding labels with the carrier sheet exposed because your machine will be damaged.
11. Label sheets should not exceed the paper weight specifications described in this User’s Guide.
12. Labels exceeding this specification may not feed or print properly and may cause damage to your machine.

1. Printing methods Printing on plain paper, recycled paper, bond paper, thin paper or thick paper Printing from the paper tray (plain paper, recycled paper and thin paper only) (For the recommended paper to use, see Type and size of paper on page 4.) Pull the paper tray completely out of the machine.
2. While pressing the green paper-guide release lever, slide the paper guides to fit the paper size.
3. Make sure that the guides are firmly in the slots.
4. Put paper in the tray and make sure: The paper is below the maximum paper mark (b b b).
5. Over filling the paper tray will cause paper jams.
6. The side to be printed on must be face down.
7. The paper guides touch the sides of the paper so it will feed properly.
8. Put the paper tray firmly back in the machine.
9. Make sure that it is completely inserted into the machine.
10. Lift up the support flap 1 to prevent paper from sliding off the face-down output tray, or remove each page as soon as it comes out of the machine.
11. Choose the following from each drop-down list of the printer driver.
12. Paper Size Media Type Paper Source For any other settings, see Driver and Software in Chapter 2.
13. Send the print data to the machine.
14. A4 Letter Executive A5 B5 B6 A6 JIS B5 A5 Long Edge Plain Paper Thin Paper Recycled Paper Tray 1

HL-2132 has no manual feed slot cover. The shared illustrations show HL-2270DW.

1. Lift support flap 1 or remove each output page immediately.
2. Set the manual-feed paper guides to the paper width.
3. With both hands insert one sheet face up until its front edge touches the feed roller; release it when the machine pulls it in.
4. Keep the sheet straight and correctly positioned.
5. Feed only one sheet at a time; inserting paper before Ready mode may eject it unprinted.
6. Choose the matching paper size and media type and Manual as Paper Source in the driver.
7. Send the print job.
8. Insert each subsequent sheet only after the printed page exits.
9. Do not open a manual-feed cover: HL-2132 does not have one.

HL-2132 has no manual feed slot cover. The shared illustrations show HL-2270DW.

1. Open the back cover for a straight path to the face-up output tray.
2. For envelopes only, lower both green levers.
3. Set the manual-feed guides to the media width.
4. Insert one complete label sheet or one envelope face up with both hands until the front edge touches the roller; release it when grabbed.
5. Keep it straight; only one item at a time, and only when Ready.
6. Choose Label or Envelopes/Env.
7. Thin/Env.
8. Thick as appropriate, the exact paper size, and Manual as Paper Source.
9. For labels choose A4 or Letter.
10. Envelope choices include Com-10, DL, C5 and Monarch; define other sizes in the driver.
11. Send the print job, then insert each next item after the prior one exits.
12. Remove printed sheets/envelopes immediately to prevent a jam or curl.
13. If an envelope is smudged, select Env.
14. Thick.
15. If a double-flap DL envelope is creased, select DL Long Edge in Windows and insert long edge first.
16. After printing envelopes, restore both green levers to their original position.
17. HL-2132 has no manual-feed slot cover.

1. Duplex printing The supplied printer drivers for Windows® 2000 or greater and Mac OS X 10.4.11 or greater all enable duplex printing.
2. For more information about how to choose the settings, see the Help text in the printer driver.
3. Guidelines for printing on both sides of the paper If the paper is thin, it may wrinkle.
4. If paper is curled, straighten it and then put it back in the paper tray or the manual feed slot.
5. If the paper continues to curl, replace the paper.
6. If the paper is not feeding properly, it may be curled.
7. Remove the paper and straighten it.
8. If the paper continues to curl, replace the paper.
9. When you use the manual duplex function, it is possible that there may be paper jams or poor print quality. (If there is a paper jam, see Paper jams and how to clear them on page 105.
10. If you have a print quality problem, see Improving the print quality on page 112.) Note Make sure that the paper tray is completely inserted to the machine.
11. You should use plain paper, recycled paper or thin paper.
12. Do not use bond paper.

1. Choose the matching paper size and a supported media type except media with a specified print side, such as envelopes or labels.
2. Select Tray 1 or Manual as Paper Source, Duplex (Manual), one of four binding types per orientation, and any required binding offset in inches or millimetres.
3. Send the job.
4. The supplied Windows driver prints the even-numbered pages first, then prompts you to reload the paper for the odd-numbered pages; follow the prompt and click OK.
5. Straighten the paper before reloading to prevent jams.
6. Very thin or thick paper is not recommended.
7. Do not select automatic Duplex: it is not supplied on HL-2132.

1. Manual Duplex Printing For Mac OS X 10.4.11 Select Paper Handling.
2. Choose Odd numbered pages and click Print.
3. Turn the paper over and reload it in the tray, and then choose Even numbered pages and click Print.
4. For Mac OS X 10.5.x and 10.6.x Select Paper Handling.
5. Choose Odd only in Pages To Print and click Print.
6. Turn the paper over and reload it in the tray, and then choose Even only in Pages To Print and click Print.

1. Basic tab You can also change settings by clicking the illustration on the left side of the Basic tab.
2. Choose Paper Size, Orientation, Copies, Media Type, Resolution and Print Settings (1).
3. Choose Multiple Page and Duplex / Booklet setting (2).
4. Choose Paper Source (3).
5. Click OK to apply your chosen settings.
6. To return to the default settings, click Default, then OK.

1. Copies The copies selection sets the number of copies that will be printed.
2. Collate With the Collate check box selected, one complete copy of your document will be printed and then will be repeated for the number of copies you selected.
3. If the Collate check box is not selected, then each page will be printed for all the copies selected before the next page of the document is printed.
4. Portrait Landscape Collate checked Collate non-checked

1. Media Type You can use the following types of media in your machine.
2. For the best print quality, select the type of media that you wish to use.
3. Note When using ordinary plain paper (75 to 105 g/m2 (20 to 28 lb)) choose Plain Paper.
4. When using heavier weight paper or rough paper choose Thick Paper or Thicker Paper.
5. For bond paper, choose Bond Paper.
6. When you use envelopes, choose Envelopes.
7. If the toner is not fixed to the envelope correctly when Envelopes has been selected, choose Env.
8. Thick.
9. If the envelope is crumpled when Envelopes has been selected, choose Env.
10. Thin.

1. Print Settings You can manually change the print setting.
2. Graphics This is the best mode for printing documents that contain graphics.
3. Text This is the best mode for printing text documents.
4. Manual You can change the settings manually by choosing Manual and clicking the Manual Settings... button.
5. You can set brightness, contrast and other settings.

1. Print Settings You can change settings by choosing a setting in the Print Settings list: Basic tab Media Type You can change the media type to one of the following: Plain Paper Thin Paper Thick Paper Thicker Paper Bond Paper Envelopes Env.
2. Thick Env.
3. Thin Recycled Paper Label Resolution You can change the resolution as follows: 300 dpi 600 dpi HQ 1200

1. Toner Save Mode You can conserve toner using this feature.
2. When you set Toner Save Mode to On, print appears lighter.
3. The default setting is Off.
4. Note We do not recommend Toner Save Mode for printing Photo or Gray Scale images.
5. Toner Save Mode is not available for HQ 1200 resolution.
6. Paper Source You can choose Auto Select, Tray 1 or Manual.
7. Reverse Print (For Mac OS X 10.4.11 only) Check Reverse Print to rotate the data by 180 degrees.
8. Advanced tab Graphics Quality You can change the print quality as follows: Graphics This is a graphics mode (contrast priority).
9. Choose this setting for printing text and figures, such as business and presentation documents.
10. You can represent sharp contrasts between shaded areas.
11. Text This is the best mode for printing text documents.
12. Skip Blank Page If Skip Blank Page is checked, the printer driver automatically detects blank pages and excludes them from printing.

1. Improve Print Output This feature allows you to improve a print quality problem.
2. Reduce Paper Curl If you choose this setting, the paper curl may be reduced.
3. If you are printing only a few pages, you do not need to choose this setting.
4. We recommend that you change the printer driver setting in Media Type to a thin setting.
5. Improve Toner Fixing If you choose this setting, the toner fixing on paper may be improved.
6. If this selection does not provide enough improvement, change the printer driver setting in Media Type to a thick setting.
7. Reduce Ghosting If you are using the machine in a high humidity environment this setting may reduce ghosting on the paper.
8. Do not use this setting if the humidity is below 30% or ghosting may increase.
9. Note This feature may not reduce ghosting for all types of paper.
10. Before you buy a lot of paper, test a small quantity to make sure that the paper is suitable.

1. Support Brother Solution Center The Brother Solutions Center (http://solutions.brother.com/) is a website offering information about your Brother product including FAQs (Frequently Asked Questions), User’s Guides, driver updates and tips for using your machine.
2. Visit the Genuine Supplies website You can visit our website for original Brother supplies by clicking this button.
3. Brother CreativeCenter You can visit our website for a free and easy online solution for business and home uses by clicking this button.

1. Multiple Page The Multiple Page selection can reduce the image size of a page allowing multiple pages to be printed on one sheet of paper or can enlarge the image size for printing one page on multiple sheets of paper.
2. Page Order When N in 1 option is selected, the page order can be selected from the drop-down list.
3. Border Line When printing multiple pages onto one sheet, with the Multiple Page feature, you can choose to have a solid border, dash border or no border around each page on the sheet.
4. Plain Paper Thin Paper Thick Paper Thicker Paper Bond Paper Envelopes Env.
5. Thick Env.
6. Thin Recycled Paper Label

1. Print cut-out line When 1 in NxN pages option is selected, the Print cut-out line option can be selected.
2. This option allows you to print a faint cut-out line around the printable area.

1. Paper Source You can choose Auto Select, Tray1, Manual and specify separate trays for printing the first page and for printing from the second page onwards.
2. Portrait Landscape Left Binding Right Binding Top Binding Bottom Binding

1. Use Watermark You can put a logo or text into your documents as a watermark.
2. You can choose one of the preset watermarks, or you can use a bitmap file or text that you have created.
3. When you use a bitmap file as a watermark, you can change the size of the watermark and put it anywhere you like on the page.
4. When you use text as a watermark, you can change the Text, Font, Style, Size and Darkness settings.

1. Header-Footer Print When this feature is enabled, it will print the date and time on your document from your computer’s system clock and the PC login user name or the text you entered.
2. By clicking Settings... you can customize the information.
3. ID Print If you select Login User Name, your PC login user name will print.
4. If you select Custom and enter the text in the Custom edit box, the text you entered will print.

1. Toner Save Mode You can conserve toner use with this feature.
2. When you set Toner Save Mode to On, print appears lighter.
3. The default setting is Off.
4. Note We do not recommend Toner Save Mode for printing Photo or Gray Scale images.
5. Toner Save Mode is not available for HQ 1200 resolution.

1. Use Reprint The machine keeps the last print job sent to it in memory.
2. You can reprint the last job without sending the data again from your computer.
3. For more information about the Reprint function, see Go button on page 60.
4. Note If you want to prevent other people from printing your data using the reprint function, uncheck the Use Reprint check box.

1. Sleep Time When the machine does not receive data for a certain period of time, it enters sleep mode.
2. In sleep mode, the machine acts as though it were turned off.
3. When you choose Printer Default, the timeout setting will be reset to the specific time set at the factory; this can be altered in the driver.
4. Intelligent Sleep Mode automatically adjusts to the most suitable timeout setting depending on the frequency of your machine use.
5. While the machine is in sleep mode, the Ready LED is dimmed, but the machine can still receive data.
6. Receiving a print file or document or pressing Go will automatically wake up the machine to start printing.

1. Sleep Time When the machine does not receive data for a certain period of time, it enters sleep mode.
2. In sleep mode, the machine acts as though it were turned off.
3. When you choose Printer Default, the timeout setting will be reset to the default time; this can be altered in the driver.
4. If you want to change the sleep time, choose Manual and then enter the time in the text box on the driver.
5. While the machine is in sleep mode, the Ready LED is dimmed, but the machine can still receive data.
6. Receiving a print file or document or pressing Go will automatically wake up the machine to start printing.

1. Improve Print Output This feature allows you to improve a print quality problem.
2. Improvement Settings Reduce Paper Curl If you choose this setting, the paper curl may be reduced.
3. If you are printing only a few pages, you do not need to choose this setting.
4. We recommend that you change the printer driver setting in Media Type to a thin setting.
5. Improve Toner Fixing If you choose this setting, the toner fixing on paper may be improved.
6. If this selection does not provide enough improvement, change the printer driver setting in Media Type to a thick setting.
7. Reduce Ghosting If you are using the machine in a high humidity environment this setting may reduce ghosting on the paper.
8. Do not use this setting if the humidity is below 30% or ghosting may increase.
9. Note This feature may not reduce ghosting for all types of paper.
10. Before you buy a lot of paper, test a small quantity to make sure that the paper is suitable.

1. Skip Blank Page If Skip Blank Page is checked, the printer driver automatically detects blank pages and excludes them from printing.
2. Note This feature does not work when you choose the following features: Use Watermark Header-Footer Print N in 1 and 1 in NxN pages in Multiple Page Duplex (Manual), Booklet, Booklet (Manual) and Duplex with Binding Offset in Duplex / Booklet (HL-2240D only) Duplex with HQ 1200 in Resolution

1. Print Profiles tab Print Profiles (1) The printer driver of the machine has the preset print profiles.
2. Select the desired profile and click OK to configure the desirable print settings easily.
3. Edit a profile (2) You can edit and save a new print profile.
4. Restore default profiles (3) Click to restore all the default print profiles.
5. Always show Print Profile tab first (4) When you always want to show the Print Profiles tab first, select this check box.

1. Editing a print profile Configure the print settings in the print driver.
2. See Basic tab on page 25 and Advanced tab on page 30.
3. Click the Print Profiles tab.
4. Click the Edit a profile button.
5. Choose the icon from the drop-down list (1) and enter a profile name (2).
6. Choose the print profile you want to overwrite and click OK.
7. Note You can overwrite the preset print profiles.

1. Tray Settings Note From the Start menu, select Printers and Faxes 1.
2. Right-click the Brother printer-series icon supplied for your model and select Properties to access the Tray Settings tab.
3. Select Settings and then Printers for Windows® 2000 users.
4. You can define the paper size for each paper tray and auto detect the serial number in the Tray Settings tab as follows.
5. Paper Source Setting (1) This feature identifies the paper size defined for each paper tray.
6. Paper Size This setting allows you to define which paper size is used for the tray and manual feed slot.
7. Highlight the paper source you want to define and then choose the paper size from the drop-down list.
8. Click Update to apply the setting to the tray.
9. Default Source This setting allows you to choose the default paper source that your document will be printed from.
10. Choose the Default Source from the drop-down list and click Update to save your setting.
11. The Auto Select setting will automatically pull paper from any paper source (tray or manual feed slot) that has a defined paper size that matches your document.

1. Serial No. (2) By clicking Auto Detect, the printer driver will query the machine and display its serial number.
2. If it fails to receive the information, the screen will display "---------------".
3. Note The Auto Detect function is not available under the following machine conditions: The machine's power switch is off.
4. The machine is in an error mode.
5. The machine is in a network shared environment.
6. The cable is not connected to the machine correctly.

1. Status Monitor This reports the machine status (any errors that may happen with the machine) when printing.
2. If you would like to turn the status monitor on, follow these steps: Click the Start button, All Programs 1 , Brother, your machine (e.g.
3. Brother HL-2270DW), and then Status Monitor.
4. Programs for Windows® 2000 users

1. Status Monitor This reports the machine status (any errors that may happen with the machine) when printing.
2. If you would like to turn the status monitor on, follow these steps: For Mac OS X 10.4.11 Run the Printer Setup Utility (from the Go menu, choose Applications, Utilities), then choose the machine.
3. Click the Utility, then the status monitor will start up.
4. For Mac OS X 10.5.x Run the System Preferences, select Print & Fax, then choose the machine.
5. Click the Open Print Queue..., then click Utility.
6. The status monitor will start up.
7. For Mac OS X 10.6.x Run the System Preferences, select Print & Fax, then choose the machine.
8. Click the Open Print Queue..., then click Printer Setup.
9. Select the Utility tab then click Open Printer Utility.
10. The status monitor will start up.

1. Choosing page setup options From an application such as Apple TextEdit, click File, then Page Setup.
2. Make sure HL-XXXX (where XXXX is your model name.) is chosen in the Format for pop-up menu.
3. You can change the settings for Paper Size, Orientation and Scale, then click OK.
4. From an application such as Apple TextEdit, click File, then Print to start printing.
5. For Mac OS X 10.4.11

1. Choosing printing options To control special printing features, choose the options in the Print dialog box.
2. For the details of available options, see the following descriptions of each option.

1. Cover Page You can make the following cover page settings: Print Cover Page If you want to add a cover page to your document, use this function.
2. Cover Page Type Choose a template for the cover page.
3. Billing Info If you want to add the billing information to the cover page, enter text in the Billing Info box.

1. How to use and install the Remote Printer Console software To use the Remote Printer Console software, follow the steps below.
2. Put the supplied installation CD-ROM into your CD-ROM drive and close the opening screen when it appears.
3. Open Windows® Explorer and choose the CD-ROM drive.
4. Double-click the tools folder.
5. Double-click the RPC folder.
6. Refer to the RPC_User’s_Guide.pdf for how to install and use the Remote Printer Console.

1. Select Booklet (Manual) to arrange pages for folding.
2. Even-numbered sides print first; follow the driver prompt to reload the paper, then click OK to print the odd-numbered sides.
3. Duplex Settings offers two binding directions per orientation, a binding offset in inches or millimetres, and Divide into Sets with 1–15 sheets per set.
4. Automatic Booklet is limited to the other listed duplex models and does not apply to HL-2132.

1. Administrator Administrators have the authority to limit access to functions such as scaling and watermark.
2. Password Enter the password into this box.
3. Set Password...
4. Click here to change the password.
5. Set Click here current password.
6. Then you can change the settings.
7. Copies Lock Lock the copy pages selection to prevent multiple copy printing.
8. Multiple Page & Scaling Lock Lock the current settings of the Multiple Page and Scaling options to prevent changes being made.
9. Watermark Lock Lock the current settings of the Watermark option to prevent changes being made.
10. Header-Footer Print Lock Lock the current settings of the Header-Footer Print option to prevent changes being made.

1. Support Note You can access the Support dialog box by clicking Support... in the Printing Preferences dialog box.
2. Brother Solutions Center (1) The Brother Solutions Center (http://solutions.brother.com/) is a website offering information about your Brother product including FAQs (Frequently Asked Questions), User’s Guides, driver updates and tips for using your machine.
3. Original Supplies Website (2) You can visit our website for original Brother supplies by clicking this button.
4. Brother CreativeCenter (3) You can visit our website for a free and easy online solution for business and home uses by clicking this button.
5. Print Settings (4) This will print the pages that show how the internal settings of the machine have been configured.
6. Check Setting... (5) You can check the current driver settings.
7. About... (6) This will show the list of the printer driver files and version information.

1. Layout Pages per Sheet Choose how many pages will appear on each side of the paper.
2. Layout Direction When you specify the pages per sheet, you can also specify the direction of the layout.
3. Border If you want to add a border, use this function.
4. Reverse Page Orientation (Mac OS X 10.5.x and 10.6.x only) Check Reverse Page Orientation to reverse the data from up to down.
5. Flip Horizontally (Mac OS X 10.6.x only) Check Flip Horizontally to print as a reflection flipped left-to-right.

1. Uninstalling the printer driver You can uninstall the printer driver that you have installed with the following steps.
2. Note This is not available if you installed the printer driver from the Windows® Add a printer function.
3. After uninstalling, we recommend that you restart your computer to remove files that were in use during the uninstall.
4. Printer driver for Windows® Click the Start button, point to All Programs 1, Brother, and then to your machine name.
5. Click UnInstall.
6. Follow the instructions on the screen.
7. Programs for Windows® 2000 users Printer driver for Macintosh For Mac OS X 10.4.11 Disconnect the USB cable between the Macintosh and your machine.
8. Log on as an ‘Administrator’.
9. Run the Printer Setup Utility (from Go menu, choose Applications, Utilities), then choose the machine you want to remove and remove it by clicking the Delete button.
10. For Mac OS X 10.5.x and 10.6.x Disconnect the USB cable between the Macintosh and your machine.
11. Log on as an ‘Administrator’.
12. From the Apple menu, choose System Preferences.
13. Click Print & Fax, then choose the machine you want to remove and remove it by clicking the - button.

1. Cancel printing Cancel the current job being printed: While printing press Go for about 4 seconds until all the LEDs light up and then release it.
2. The Ready and Error LEDs will flash as the job is being canceled.
3. Cancel all the received jobs: To delete all jobs, press Go for about 4 seconds until all the LEDs light up and then release it.
4. Press Go again.
5. The Ready and Error LEDs will flash as the job(s) is being canceled.

1. Error recovery If there is an error, the machine will recover automatically from some errors.
2. If an error is not automatically cleared, press Go to clear the error, and then continue to use the machine.

1. Reprint To reprint the last document, press Go for about 4 seconds until all the LEDs light up and then release it.
2. Within 2 seconds press Go the number of times you want to reprint.
3. If you don’t press Go within 2 seconds, a single copy will be printed.
4. If you print with the Windows® printer driver we have supplied with the printer, the settings for Use Reprint in the printer driver will take priority over the settings made on the control panel. (For more information, see Use Reprint on page 32.)

1. Print a test page You can use Go or the printer driver to print a test page.
2. Using the Go button Turn off the machine.
3. Make sure that the front cover is closed and the power cord is plugged in.
4. Hold down Go as you turn on the power switch.
5. Keep Go pressed down until the Toner, Drum and Error LEDs light up.
6. Release Go.
7. Make sure that the Toner, Drum and Error LEDs are off.
8. Press Go again.
9. The machine will print a test page.
10. Using the printer driver If you are using the Windows® printer driver, click the Print Test Page button in the General tab of the printer driver.

1. Do not connect the interface cable yet.
2. Connect the power cord to the machine and an AC socket.
3. Turn on the power switch.
4. After warm-up, the Ready LED stops blinking and stays green.
5. Press Go to print a test page and confirm it printed correctly.
6. This initial test function is unavailable after sending the first print job from the computer; the operation guide documents the separate later test-page sequence.

1. Print a Printer Settings page You can print the current settings using the control panel button or printer driver.
2. Using the Go button Make sure that the front cover is closed and the power cord is plugged in.
3. Turn on the machine and wait until the machine is in Ready mode.
4. Press Go three times within 2 seconds.
5. The machine will print the current printer settings page.
6. Using the printer driver If you are using the Windows® printer driver, you can print the current printer settings page by clicking the Print Settings button in the Support dialog.

1. Factory Reset You can partially reset the machine back to its default printer settings.
2. The network settings will not be reset: Turn off the machine.
3. Make sure that the front cover is closed and the power cord is plugged in.
4. Hold down Go as you turn on the power switch.
5. Keep Go pressed down until all the LEDs light up and the Ready LED turns off.
6. Release Go.
7. Make sure that all the LEDs turn off.
8. Press Go eight times.
9. Make sure that all the LEDs light up to indicate the machine has been reset to its factory default settings (except the network settings).
10. The machine will restart.
11. The page counter cannot be changed.

1. Settings Reset This operation will reset all the machine settings back to the settings that were set at the factory: Turn off the machine.
2. Make sure that the front cover is closed and the power cord is plugged in.
3. Hold down Go as you turn on the power switch.
4. Keep Go pressed down until all the LEDs light up and the Ready LED turns off.
5. Release Go.
6. Make sure that all the LEDs turn off.
7. Press Go ten times.
8. The machine will automatically restart.
9. The page counter cannot be changed.

1. Before replacing the consumable items Please read the following instructions before replacing the consumable items.
2. WARNING DO NOT put a toner cartridge into a fire.
3. It could explode, resulting in injuries.
4. DO NOT use flammable substances, any type of spray or any organic solvent/liquids containing alcohol or ammonia to clean the inside or outside of the machine.
5. Doing this may cause a fire or electrical shock.
6. See Cleaning on page 83 for how to clean the machine.
7. Be careful not to inhale toner.
8. HOT SURFACE After you have just used the printer, some internal parts will be extremely hot.
9. Wait at least 10 minutes for the printer to cool down before continuing to the next step.
10. To prevent any degradation to the print quality, DO NOT touch the shaded parts shown in the illustrations.
11. IMPORTANT Brother machines are designed to work with toner of a particular specification and will work to a level of optimum performance when used with genuine Brother branded toner cartridges.
12. Brother cannot guarantee this optimum performance if toner or toner cartridges of other specifications are used.
13. Brother does not therefore recommend the use of cartridges other than genuine Brother branded cartridges with this machine.
14. If damage is caused to the drum unit or other part of this machine as a result of using other manufacturer’s products with this machine, any repairs required as a result may not be covered by the warranty.
15. We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a piece of disposable paper underneath it in case you accidentally spill or scatter toner.
16. Handle the toner cartridge carefully.
17. If toner scatters on your hands or clothes, immediately wipe or wash it off with cold water.
18. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
19. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
20. We recommend that you clean the machine when you replace the consumables.
21. See Cleaning on page 83.
22. DO NOT unpack a spare toner cartridge until immediately before you put it into the machine.
23. If toner cartridges are left unpacked for a long time the toner life may be shortened.
24. DO NOT unpack a spare drum unit until immediately before you put it into the machine.
25. If drum unit is exposed to sunlight or room light the unit may be damaged.
26. While removing the drum unit, handle it carefully because it may contain toner.
27. Note Be sure to seal up the used toner cartridge tightly in a suitable bag so that toner powder does not spill out of the cartridge.
28. Go to http://www.brother.eu/recycle/ for instructions on how to return the used toner cartridge to the Brother collection program.
29. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste.
30. If you have questions, call your local waste disposal office.
31. To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges.
32. When you want to buy toner cartridges, call your dealer.

1. Before replacing the consumable items Please read the following instructions before replacing the consumable items.
2. WARNING DO NOT put a toner cartridge into a fire.
3. It could explode, resulting in injuries.
4. DO NOT use flammable substances, any type of spray or any organic solvent/liquids containing alcohol or ammonia to clean the inside or outside of the machine.
5. Doing this may cause a fire or electrical shock.
6. See Cleaning on page 83 for how to clean the machine.
7. Be careful not to inhale toner.
8. HOT SURFACE After you have just used the printer, some internal parts will be extremely hot.
9. Wait at least 10 minutes for the printer to cool down before continuing to the next step.
10. To prevent any degradation to the print quality, DO NOT touch the shaded parts shown in the illustrations.
11. IMPORTANT Brother machines are designed to work with toner of a particular specification and will work to a level of optimum performance when used with genuine Brother branded toner cartridges.
12. Brother cannot guarantee this optimum performance if toner or toner cartridges of other specifications are used.
13. Brother does not therefore recommend the use of cartridges other than genuine Brother branded cartridges with this machine.
14. If damage is caused to the drum unit or other part of this machine as a result of using other manufacturer’s products with this machine, any repairs required as a result may not be covered by the warranty.
15. We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a piece of disposable paper underneath it in case you accidentally spill or scatter toner.
16. Handle the toner cartridge carefully.
17. If toner scatters on your hands or clothes, immediately wipe or wash it off with cold water.
18. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
19. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
20. We recommend that you clean the machine when you replace the consumables.
21. See Cleaning on page 83.
22. DO NOT unpack a spare toner cartridge until immediately before you put it into the machine.
23. If toner cartridges are left unpacked for a long time the toner life may be shortened.
24. DO NOT unpack a spare drum unit until immediately before you put it into the machine.
25. If drum unit is exposed to sunlight or room light the unit may be damaged.
26. While removing the drum unit, handle it carefully because it may contain toner.
27. Note Be sure to seal up the used toner cartridge tightly in a suitable bag so that toner powder does not spill out of the cartridge.
28. Go to http://www.brother.eu/recycle/ for instructions on how to return the used toner cartridge to the Brother collection program.
29. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste.
30. If you have questions, call your local waste disposal office.
31. To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges.
32. When you want to buy toner cartridges, call your dealer.
33. REPLACE TONER The machine will stop printing until you replace the toner cartridge.
34. A new and unused original Brother toner cartridge will reset the REPLACE TONER mode.
35. Replacing the toner cartridge Before you replace the toner cartridges, see Before replacing the consumable items on page 67.
36. Make sure that the machine is turned on.
37. Leave the machine for at least 10 minutes to cool down.
38. Open the front cover.
39. Take out the drum unit and toner cartridge assembly.
40. IMPORTANT We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner.
41. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
42. Push down the green lock lever and take the toner cartridge out of the drum unit.
43. Unpack the new toner cartridge.
44. Hold the cartridge level with both hands and gently shake it from side to side several times to spread the toner evenly inside the cartridge.
45. Pull off the protective cover.
46. Put the new toner cartridge firmly into the drum unit until you hear it lock into place.
47. If you put it in properly, the green lock lever will lift automatically.
48. Clean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and left to right several times.
49. Note Be sure to return the tab to the home position (a) (1).
50. If you do not, printed pages may have a vertical stripe.
51. Put the drum unit and toner cartridge assembly back into the machine.
52. Close the front cover.
53. Note DO NOT turn off the machine's power switch or open the front cover until the Ready LED lights up.

Diagram key

• Insertion arrow: Put the new toner cartridge firmly into the drum unit.
• Magnified green lever: The lever lifts automatically when the toner cartridge locks correctly.
• Check mark: Correctly locked cartridge with the green lever raised.
• Cross mark: Incorrectly seated cartridge; fit it firmly until it locks.

1. The printing operation varies depending on the machine setting: Default setting (Stop mode) The machine will stop printing until you replace the toner cartridge with a new one when the LEDs indicate REPLACE TONER.
2. Continue mode To force the machine to continue printing after the LEDs indicate REPLACE TONER, press Go seven times to enter Continue mode (all the LEDs flash twice, and then the Ready LED turns on).
3. The machine will continue printing until the LEDs indicate TONER ENDED.
4. To return to the default setting (Stop mode), press Go seven times (all the LEDs flash once).
5. Note Make sure that the front cover is closed before you change the mode.
6. When the LEDs indicate an error mode, you cannot change the mode.
7. If you continue printing in the Continue mode, we cannot guarantee the print quality.
8. While using Continue mode the print may appear faint.
9. Ready mode When you replace the toner cartridge with a new one, the machine returns to Ready mode.
10. TONER ENDED The machine stops printing until you replace the toner cartridge with a new one.
11. See Replacing the toner cartridge on page 71.

1. Drum unit A new drum unit can print approximately 12,000 A4 or Letter size single-sided pages at 1 page / job.
2. Note There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on.
3. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
4. The actual number of pages that your drum will print may be significantly less than this estimate.
5. Because we have no control over the many factors that determine the actual drum life, we cannot guarantee a minimum number of pages that will be printed by your drum.
6. For best performance, use only genuine Brother toner.
7. The machine should be used only in a clean, dust- free environment with adequate ventilation.
8. Printing with a non-Brother drum unit may reduce not only the print quality but also the quality and life of the machine itself.
9. Warranty coverage does not apply to problems caused by the use of a non-Brother drum unit.
10. DRUM END SOON If the Drum LED flashes, it means the drum unit will need to be replaced soon.
11. We recommend that you replace the drum unit with a new one before there is a noticeable deterioration in the print quality.
12. REPLACE DRUM If the Drum LED is on, it means the drum unit should be replaced.
13. Please replace it with a new Brother drum unit.
14. DRUM STOP If the Drum and Error LEDs are on, it means the drum unit must be replaced.
15. Replace it with a new Brother drum unit.

This manual sequence starts with the Drum LED flashing. Current exact-model support also provides a sequence for the steady REPLACE DRUM indication. Reset the drum counter only when fitting a new drum, never for toner alone.

1. Before replacing the consumable items Please read the following instructions before replacing the consumable items.
2. WARNING DO NOT put a toner cartridge into a fire.
3. It could explode, resulting in injuries.
4. DO NOT use flammable substances, any type of spray or any organic solvent/liquids containing alcohol or ammonia to clean the inside or outside of the machine.
5. Doing this may cause a fire or electrical shock.
6. See Cleaning on page 83 for how to clean the machine.
7. Be careful not to inhale toner.
8. HOT SURFACE After you have just used the printer, some internal parts will be extremely hot.
9. Wait at least 10 minutes for the printer to cool down before continuing to the next step.
10. To prevent any degradation to the print quality, DO NOT touch the shaded parts shown in the illustrations.
11. IMPORTANT Brother machines are designed to work with toner of a particular specification and will work to a level of optimum performance when used with genuine Brother branded toner cartridges.
12. Brother cannot guarantee this optimum performance if toner or toner cartridges of other specifications are used.
13. Brother does not therefore recommend the use of cartridges other than genuine Brother branded cartridges with this machine.
14. If damage is caused to the drum unit or other part of this machine as a result of using other manufacturer’s products with this machine, any repairs required as a result may not be covered by the warranty.
15. We recommend that you place the drum unit and toner cartridge assembly on a clean, flat surface with a piece of disposable paper underneath it in case you accidentally spill or scatter toner.
16. Handle the toner cartridge carefully.
17. If toner scatters on your hands or clothes, immediately wipe or wash it off with cold water.
18. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
19. To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
20. We recommend that you clean the machine when you replace the consumables.
21. See Cleaning on page 83.
22. DO NOT unpack a spare toner cartridge until immediately before you put it into the machine.
23. If toner cartridges are left unpacked for a long time the toner life may be shortened.
24. DO NOT unpack a spare drum unit until immediately before you put it into the machine.
25. If drum unit is exposed to sunlight or room light the unit may be damaged.
26. While removing the drum unit, handle it carefully because it may contain toner.
27. Note Be sure to seal up the used toner cartridge tightly in a suitable bag so that toner powder does not spill out of the cartridge.
28. Go to http://www.brother.eu/recycle/ for instructions on how to return the used toner cartridge to the Brother collection program.
29. If you choose not to return your used toner cartridge, please discard the used toner cartridge according to local regulations, keeping it separate from domestic waste.
30. If you have questions, call your local waste disposal office.
31. To ensure high quality printing, we recommend that you use only genuine Brother toner cartridges.
32. When you want to buy toner cartridges, call your dealer.
33. Replacing the drum unit Before you replace the drum unit, see Before replacing the consumable items on page 67.
34. When you replace the drum unit with a new one, you need to reset the drum counter by completing the following steps: Make sure that the machine is turned on and the Drum LED is flashing.
35. Leave the machine for at least 10 minutes to cool down.
36. Open the front cover.
37. Take out the drum unit and toner cartridge assembly.
38. IMPORTANT We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner.
39. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
40. Push down the green lock lever and take the toner cartridge out of the drum unit.
41. Unpack the new drum unit.
42. Put the toner cartridge firmly into the new drum unit until you hear it lock into place.
43. If you put the cartridge in properly, the green lock lever will lift automatically.
44. Put the drum unit and toner cartridge assembly back into the machine.
45. Do not close the front cover yet.
46. Press and hold down Go for about 4 seconds until all the LEDs light up.
47. Once all four LEDs are lit, release Go.
48. IMPORTANT Do not reset the drum counter when you only replace the toner cartridge.
49. Close the front cover.
50. Make sure that the Drum LED is now off.

1. Cleaning Clean the outside and inside of the machine regularly with a dry, lint-free cloth.
2. When you replace the toner cartridge or the drum unit, make sure that you clean the inside of the machine.
3. If printed pages are stained with toner, clean the inside of the machine with a dry, lint-free cloth.
4. WARNING DO NOT use flammable substances, any type of spray or any organic solvent/liquid that contains alcohol or ammonia to clean the inside or outside of the machine.
5. Doing this may cause a fire or electrical shock.
6. Be careful not to inhale toner.
7. IMPORTANT Use neutral detergents.
8. Cleaning with volatile liquids such as thinner or benzine will damage the surface of the machine.

1. Cleaning the outside of the machine Turn off the machine's power switch.
2. Disconnect all cables, and then unplug the power cord from the AC power outlet.
3. Pull the paper tray completely out of the machine.
4. Wipe the outside of the machine with a dry, lint-free cloth to remove dust.
5. Remove all the paper, and anything that is stuck inside, from the paper tray.
6. Wipe the inside of the paper tray with a dry, lint-free cloth to remove dust.
7. Put the paper back in the paper tray.
8. Put the paper tray back in the machine.
9. Plug the machine's power cord back into the AC power outlet first, and then reconnect all cables.
10. Turn on the machine's power switch.

1. Cleaning the corona wire If you have print quality problems, clean the corona wire as follows: Open the front cover and leave the machine for at least 10 minutes to cool down.
2. Take out the drum unit and toner cartridge assembly.
3. IMPORTANT We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner.
4. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
5. Clean the primary corona wire inside the drum unit by gently sliding the green tab from right to left and left to right several times.
6. Note Be sure to return the tab to the home position (a) (1).
7. If you do not, printed pages may have a vertical stripe.
8. Put the drum unit and toner cartridge assembly back into the machine.
9. Close the front cover.

Diagram key

• Curved movement arrow: Gently slide the green tab right to left and left to right several times.
• Left arrow in enlarged view: Slide the same green tab during cleaning.
• 1: Home position for the green tab.
• Triangle on the tab: Align the tab with the home-position triangle after cleaning.
• Triangle on the housing: Home-position marker.

HL-2132 has no manual feed slot cover. The shared illustrations show HL-2270DW.

1. For white or black spots at 94 mm (3.71 in.) intervals, prepare blank A4 or Letter paper and wait for Ready.
2. Open the front and back covers.
3. Confirm that both green envelope levers are up.
4. Press Go five times and close the front cover; wait until Ready turns on for drum cleaning.
5. HL-2132 has no manual-feed slot cover to open.
6. Use both hands to set the guides to paper width, then feed one blank sheet until the roller grabs it and let go.
7. Ready flashes during cleaning.
8. Reverse OPC rotation makes a mechanical noise; this is normal.
9. Feed only one sheet, straight and correctly positioned, to avoid a skewed print or jam.
10. Any size other than A4 or Letter stops cleaning and is ejected.
11. Do not close the back cover during cleaning: it stops cleaning, ejects the sheet and may cause a jam.
12. A print job received before feeding the sheet stops cleaning and prints that job.
13. Wait until the machine returns to Ready.
14. Repeat from opening both covers through completed cleaning two more times, each with a new blank sheet.
15. Discard the used paper.

1. If the problem is not solved yet, follow the steps below: Turn off the machine's power switch.
2. Disconnect all the cables, and then unplug the power cord from the AC power outlet.
3. Leave the machine turned off for at least 10 minutes to cool down.
4. Open the front cover.
5. Take out the drum unit and toner cartridge assembly.
6. IMPORTANT We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner.
7. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
8. Push down the green lock lever and take the toner cartridge out of the drum unit.
9. IMPORTANT To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.
10. Put the print sample in front of the drum unit, and find the exact position of the poor print.
11. Turn the drum unit gear by hand while looking at the surface of the OPC drum (1).
12. When you have found the mark on the drum that matches the print sample, wipe the surface of the OPC drum with a dry cotton swab until the dust or glue on the surface comes off.
13. IMPORTANT DO NOT clean the surface of the photosensitive drum with a sharp object.
14. Put the toner cartridge back into the drum unit until you hear it lock into place.
15. If you put the cartridge in properly, the green lock lever will lift automatically.
16. Open the front cover.
17. Put the drum unit and toner cartridge assembly back into the machine.
18. Put the paper tray firmly back in the machine.
19. Close the front cover.
20. Plug the machine's power cord back into the AC power outlet first, and then reconnect all cables.
21. Turn on the machine's power switch.

Diagram key

• Curved arrow in the enlarged view: Turn the drum unit gear by hand while watching the OPC surface.
• Curved arrow on the drum assembly: The same drum gear is turned by hand while watching the OPC surface.
• 1: Surface of the OPC drum.

1. Cleaning the paper pick-up roller If the paper pick-up roller is dirty, the machine may not feed paper.
2. In that case, clean the paper pick-up roller as follows: Turn off the machine's power switch.
3. Disconnect all cables, and then unplug the power cord from the AC power outlet.
4. Pull the paper tray out of the machine.
5. Remove all the paper, and anything that is stuck inside, from the paper tray.
6. Tightly wring out a lint-free cloth soaked in lukewarm water, and then in the paper tray wipe the separator pad (1) to remove any dust.
7. Wipe the two paper pick-up rollers (1) inside the machine.
8. Put the paper back in the paper tray.
9. Put the paper tray back in the machine.
10. Plug the machine's power cord back into the AC power outlet first, and then reconnect all cables.
11. Turn on the machine's power switch.

Diagram key

• 1: Separator pad in the paper tray.

Diagram key

• 1: The two paper pick-up rollers inside the machine.

1. Packing and shipping the machine Note If for any reason you must ship your machine, carefully repack the machine in the original packaging to avoid any damage during transit.
2. The machine should be adequately insured with the carrier.
3. Turn off the machine's power switch.
4. Disconnect all the cables, and then unplug the power cord from the AC power outlet.
5. Leave the machine turned off for at least 10 minutes to cool down.
6. Open the front cover.
7. Take out the drum unit and toner cartridge assembly.
8. IMPORTANT We recommend that you put the drum unit and toner cartridge assembly on a piece of disposable paper or cloth in case you accidentally spill or scatter toner.
9. To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.
10. Put the protective material in the machine with the "REMOVE" text to the left, as shown in the illustration.
11. Put the drum unit and toner cartridge assembly back into the machine.
12. Put the elastic band over the handle of the drum unit, as shown in the illustration.
13. Close the front cover.
14. Put the machine into the bag it originally came in.
15. Put the styrofoam piece marked "RIGHT" on the right side of the machine.
16. Put the styrofoam piece marked "LEFT" on the left side of the machine.
17. Put the machine into the original carton.
18. RIGHT LEFT Put the AC power cord and printed materials in the original carton as shown in the illustration.
19. Close the carton and tape it shut.

HL-2132 has no automatic duplex tray. The shared jam procedure steps j–m are for duplex models and are excluded; all applicable steps a–i and n–t, cautions and checks are retained.

1. Keep both the toner cartridge and drum installed correctly.
2. When adding paper, first remove all paper from the tray and straighten the stack to prevent multiple feeding.
3. If a jam occurs, the Error LED flashes.
4. Internal parts can be extremely hot: do not touch the shaded sensitive parts shown in the source illustrations.
5. Open the front cover and leave the printer switched on for at least 10 minutes to cool.
6. Slowly remove the drum and toner assembly; the jammed paper may come out with it or become accessible.
7. If the assembly cannot be removed easily, do not force it; proceed directly to pulling out the paper tray.
8. If it was removed, place it on disposable paper or cloth to contain toner, do not touch the electrodes because of static electricity, and close the front cover without reinstalling it yet.
9. Pull the paper tray completely out and use both hands to slowly remove jammed paper.
10. Open the back cover.
11. Pull down the left and right tabs to open the fuser cover.
12. Use both hands to gently remove paper from the fuser unit.
13. Close the fuser cover and back cover.
14. Insert the paper tray firmly.
15. If the drum and toner assembly could not be removed earlier, remove it now before continuing.
16. Push down the green lock lever and remove the toner cartridge from the drum.
17. Clear any paper inside the drum unit.
18. Handle toner carefully; immediately wipe or wash toner from hands or clothing with cold water, and do not touch the shaded sensitive parts.
19. Refit the toner cartridge until it clicks; the green lock lever rises automatically when correctly seated.
20. Open the front cover and reinstall the drum and toner assembly, then close the front cover.
21. Confirm that Error is off and Ready is on.
22. Once all jammed paper is removed, inserting the paper tray and then closing the front cover resumes printing automatically.
23. If printing does not resume, press Go.
24. If it still does not print, check that every remaining piece of jammed paper has been removed, then try again.
25. The duplex-tray steps apply to other models and are absent from this HL-2132 procedure.

Diagram key

• Left downward arrow: Pull down the tab on the left-hand side.
• Right downward arrow: Pull down the tab on the right-hand side.
• Central downward arrow: Open the fuser cover after pulling down both side tabs.
• 1: Fuser cover.

1. Before buying a large quantity, check that the paper is suitable for laser printers and test a small quantity.
2. Brother recommends 75–90 g/m² paper, long-grain fibres and neutralized rather than acid paper.
3. An acid-paper check pen distinguishes acid from neutral paper.
4. Check the packaging for the print side and follow its instructions; the opening side of the ream package is usually the print side.
5. Paper typically contains about 5% water by weight and may absorb about 10% in high humidity, impairing toner fixing.
6. Brother recommends 50–60% surrounding humidity for storing and using paper.
7. Unrecommended paper may cause jams or misfeeds.

1. For technical or operational help, contact the country where you bought the printer, from within that country.
2. Use Brother’s official support site for driver updates, manuals, FAQs and troubleshooting tips.
3. Register the product through Brother’s registration service.
4. For European service centres, contact the local Brother office using the country selection on the official Brother site.

1. Place the printer on a flat, level, stable surface without vibration or shocks, near a grounded electrical socket.
2. Keep the temperature between 10°C and 32.5°C and humidity between 20% and 80%, without condensation.
3. Avoid direct sunlight, excessive heat, flames, corrosive gases, moisture, dust, heaters, air conditioners, desk fans, refrigerators, water, chemicals and high-traffic areas.
4. Leave roughly 100 mm between ventilation holes and a wall.
5. Avoid switched/timed sockets and circuits with large appliances.
6. Keep cables from causing a trip hazard, and avoid interference sources.
7. Discard the silica pack; do not eat it, and seek medical attention immediately if swallowed.

1. Unplug the power cord before cleaning inside the printer.
2. Do not handle the plug with wet hands; insert it fully.
3. Keep an easily accessible electrical socket nearby so that power can be disconnected completely in an emergency.
4. Keep plastic packing bags away from babies and children and dispose of them properly.
5. Do not use flammable substances near the printer or sprays to clean it.
6. Do not vacuum scattered toner: use a dry, lint-free soft cloth and dispose of the toner according to local regulations.
7. Avoid inhaling toner.
8. After use, internal parts can be extremely hot; do not touch the shaded parts shown in the safety illustrations when opening front or rear covers.
9. Do not remove or damage internal warning labels.

1. Read and save all safety instructions, and follow every warning and instruction marked on the printer.
2. Unplug it before cleaning inside; do not use liquid or aerosol cleaners, and use a dry, lint-free soft cloth.
3. Do not place it on an unstable cart, stand or table.
4. Keep all casing ventilation openings clear: do not set it on a bed, sofa, rug or similar surface, near or over a radiator or heater, or in a built-in installation without adequate ventilation.
5. Use an AC source within the rating-label range; never use DC or an inverter, and consult a qualified electrician if unsure.
6. The three-wire grounded plug must connect to a grounded outlet; if it will not fit, have an electrician replace the obsolete outlet, and never defeat the grounding.
7. Use only the supplied power cord.
8. Do not rest objects on it or place it where people can walk on it.
9. Use a well-ventilated area.
10. The power cord, including extensions, must be no longer than 5 metres (16.5 feet); do not share its circuit with high-powered appliances such as an air conditioner, copier or shredder.
11. Keep the printed-page path clear, and wait until pages have exited before picking them up.
12. Unplug the printer and refer service to Brother Authorized Service Personnel if the cord is damaged or frayed, liquid enters it, it is exposed to rain or water, it does not work normally when the operating instructions are followed, it is dropped or its casing is damaged, or its performance changes distinctly.
13. Adjust only controls covered by the operating instructions; other adjustments may damage it and require extensive qualified repair.
14. Brother recommends a surge protector.
15. Do not use it near water-using appliances, a swimming pool, in a wet basement, during an electrical storm, or near a gas leak.
16. The telephone gas-leak-reporting condition in the shared source is MFC-only and does not apply to this printer.

1. Disconnect device This product must be installed near an electrical socket that is easily accessible.
2. In case of emergencies, you must disconnect the power cord from the electrical socket to shut off power completely.

1. For 220–240 V models, the product is a Class 1 laser product.
2. The internal Class 3B diode emits invisible laser radiation in the scanner unit; never open that unit.
3. Do not use controls, adjustments or procedures other than those specified in the manual: hazardous radiation exposure may result.

1. Wiring information (U.K. only) If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the same rating as the original fuse.
2. Always replace the fuse cover.
3. Never use a plug that does not have a cover.
4. If in any doubt, call a qualified electrician.
5. Warning -This product must be earthed.
6. The wires in the mains lead are coloured in line with the following code: Green and Yellow: Earth Blue: Neutral Brown: Live

1. EU Directive 2002/96/EC and EN50419 This equipment is marked with the above recycling symbol.
2. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream.
3. This will benefit the environment for all. (European Union only)

1. Open Source Licensing Remarks This product includes open-source software.
2. Please see Open Source Licensing Remarks and Copyright information on the supplied CD-ROM. (For Windows®) “X:\License.txt” (where X is your drive letter). (For Macintosh) Double-click the CD-ROM icon on your desktop.
3. Then double-click the Utilities icon.
4. License.rtf will appear.

1. Do not connect the AC power cord yet.
2. Read the Safety and Legal booklet before setup.
3. Remove exterior packing tape and the silica pack from the face-down output tray.
4. Keep plastic bags away from children, and do not eat the silica pack; seek medical attention if swallowed.
5. Open the front cover.
6. Remove the elastic band, lift the paper strip to remove protective material, then remove the drum and toner assembly.
7. Gently shake it side to side several times to distribute toner evenly.
8. Reinsert it and close the front cover.
9. Do not connect the USB interface cable yet; check that the delivered components and power cord suit your country.
10. Keep the original packing for shipping.

1. Pull the paper tray completely out.
2. Hold the green paper-guide release lever and slide the guides to the correct paper size, seating them firmly in their slots.
3. Fan the paper stack to prevent jams and misfeeds.
4. Put paper below the maximum mark, print side face down, with guides touching the sides.
5. Reinsert the tray completely and flush with the machine.
6. Use only sizes available for the selected model and region; this UK HL-2132 reference uses its operation-guide tray sizes.

1. This CD-ROM setup describes the Windows versions listed in the guide.
2. Switch on the computer, log in with Administrator rights and close running programs.
3. Turn the printer off and leave its USB cable disconnected; disconnect an already connected cable.
4. Insert the supplied CD-ROM, choose model/language when prompted, then click Install Printer Driver and accept the license if agreed.
5. If the screen does not open automatically, open My Computer/Computer, the CD-ROM drive and start.exe.
6. Follow the screen instructions to the USB connection prompt.
7. Connect the USB cable directly to the computer, then switch the printer on and follow the remaining setup instructions.
8. Permit the installer’s User Account Control or security/antivirus prompt when applicable.
9. The XML Paper Specification driver is identified for applications using that format; consult current official driver support for present operating systems.

1. This guide describes Mac OS X 10.4.11–10.6.x; it says to upgrade 10.4.0–10.4.10 before installation.
2. Start the Macintosh, log in with Administrator rights and plug in the printer.
3. Connect the USB cable directly to the printer and Macintosh; do not use a keyboard USB port or an unpowered hub.
4. Turn the printer on.
5. Insert the CD-ROM, double-click Start Here OSX, and follow the instructions, allowing a few minutes for installation.
6. Select the machine and click OK, then Next.
7. Choose the desired Brother Support options if its screen appears.
8. Consult current official support for newer systems.

1. Close the front cover and connect the power cord.
2. Turn the printer on and wait for Ready.
3. Press Go three times within 2 seconds to print the settings.
4. The shared guide’s network settings apply to other named models; HL-2132 is USB-only.

1. Read Safety and Legal before setup.
2. Check all components; contents vary by country, and the interface cable is not supplied.
3. Keep the original packaging for shipping and insure the printer adequately with the carrier.
4. Use a USB 2.0 Type A/B cable no longer than 2 metres.
5. Keep packing bags away from babies and children and dispose of them properly.
6. The setup clearance drawing specifies at least 100 mm on the left, right and above the printer, and 120 mm behind it.
7. Follow the separate Safety and Legal location requirements.

Diagram key

• Top clearance arrow: Keep a minimum 100 mm (4 in.) above the printer.
• Left clearance arrow: Keep a minimum 100 mm (4 in.) on the left.
• Right clearance arrow: Keep a minimum 100 mm (4 in.) on the right.
• Rear clearance arrow: Keep a minimum 120 mm (4.72 in.) behind the printer.

1. The setup table depicts all four LEDs off when the printer is off.
2. In Sleep or Deep Sleep, only Ready is dimmed; in Ready, only Ready is on.
3. Warming up or cooling down flashes Ready on and off at 1-second intervals.
4. Receiving data or remaining data flashes Ready on and off at 0.5-second intervals.
5. Toner Low flashes Toner on for 2 seconds and off for 3 seconds, with Ready on.
6. Replace Toner in the table’s Stop mode has Toner on and all other LEDs off; Toner Ended has Toner and Error on, Drum and Ready off.
7. Drum End Soon flashes Drum on for 2 seconds and off for 3 seconds, with Ready on.
8. Replace Drum has Drum and Ready on, Toner and Error off.
9. Cover Open or Paper Jam flashes Error at 0.5-second intervals, with the other LEDs off.
10. No Paper has Error on and the other LEDs off.
11. Drum Error flashes Drum and Error at 0.5-second intervals, with Toner and Ready off.
12. Drum Stop has Drum and Error on, Toner and Ready off.
13. Service call error flashes all LEDs at 0.5-second intervals.
14. The table refers to the complete User’s Guide remedies.
15. Pressing Go seven times selects toner Continue mode, makes all LEDs flash twice and then turns Ready on; printing continues until Toner Ended.
16. Preserve the operation guide’s precautions for changing this mode.