Keep the robot charged. Scheduled cleaning can only begin when the battery level is above 20%.
Keep the robot charged. Scheduled cleaning can only begin when the battery level is above 20%.
The robot does not resume cleaning after recharging2 checks
Make sure that the robot is not in DND mode. DND mode will prevent auto top-up.
Make sure that the robot is not in DND mode. DND mode will prevent auto top-up.
If the robot is placed manually on the dock or sent to dock by pressing buttons, it will not be able to resume cleaning.
If the robot is placed manually on the dock or sent to dock by pressing buttons, it will not be able to resume cleaning.
Slow charging2 checks
When used at high or low temperatures, the robot will automatically reduce its charging speed to extend battery life.
When used at high or low temperatures, the robot will automatically reduce its charging speed to extend battery life.
Charging contacts dirty. Wipe them with a soft, dry cloth.
Charging contacts dirty. Wipe them with a soft, dry cloth.
Is power always being drawn when the robot is on the dock?1 check
The robot will draw power while it is docked to maintain battery performance, but the power consumption is extremely low.
The robot will draw power while it is docked to maintain battery performance, but the power consumption is extremely low.
Does the robot need to be charged for at least 16 hours for the first three uses?1 check
No. Lithium-ion batteries have no memory effect. The robot can be used once fully charged.
No. Lithium-ion batteries have no memory effect. The robot can be used once fully charged.
Unable to auto-empty4 checks
Auto-emptying is disabled. Check in-app settings.
Auto-emptying is disabled. Check in-app settings.
Dust bag is not installed. Check and install.
Dust bag is not installed. Check and install.
Auto-emptying will not be triggered if the robot returns to the dock without cleaning.
Auto-emptying will not be triggered if the robot returns to the dock without cleaning.
The robot will not auto-empty after returning to the dock in DND mode. Adjust the cleaning time or DND period.
The robot will not auto-empty after returning to the dock in DND mode. Adjust the cleaning time or DND period.
Reduced emptying performance or unusual noise when emptying2 checks
The main brush or main brush cover is not properly installed. Check and install in place.
The main brush or main brush cover is not properly installed. Check and install in place.
The filter, air duct, disposable dust bag, suction inlet, air inlet, or dustbin is blocked. Clean to remove blockages.
The filter, air duct, disposable dust bag, suction inlet, air inlet, or dustbin is blocked. Clean to remove blockages.
The status indicator light is steady red1 check
The dust bag is not in place. Check and install in place.
The dust bag is not in place. Check and install in place.
The robot begins to miss certain spots1 check
The cliff sensors may be dirty. Clean them with a soft, dry cloth.
The cliff sensors may be dirty. Clean them with a soft, dry cloth.
No or little water during mopping2 checks
Use the mobile app to increase the water flow.
Use the mobile app to increase the water flow.
Check whether there is water in the water tank and check the manual for instructions on how to correctly install the dustbin and water tank combo unit, mop cloth mount and mop cloth.
Check whether there is water in the water tank and check the manual for instructions on how to correctly install the dustbin and water tank combo unit, mop cloth mount and mop cloth.
The robot cannot return to the charging dock when it has been moved manually1 check
After a significant position change, the robot will re-generate the map. If the charging dock is too far away, it may not be able to return to recharge and must be placed on the charging dock manually.
After a significant position change, the robot will re-generate the map.
If the charging dock is too far away, it may not be able to return to recharge and must be placed on the charging dock manually.
Guides
Product overview
Instructions from the manual
Robot controls and power indicator7 steps
Hold Power/Clean to turn on or off; press to clean.
Press Dock to start docking.
Any button pauses a running robot.
Steady white means waiting, paused, WiFi connected, cleaning, docking, mapping or emptying.
Breathing white means startup or charging above 20%battery; slowly flashing white means waiting for WiFi; quickly flashing white means updating or connecting.
Steady red means below 20%battery; breathing red means charging below 20%; flashing red means error.
The manual does not assign an indicator at exactly 20%.
Complete Power/Clean and Dock controls and all printed power/WiFi status explanations. Q7 TF+ CE; base and FCC versions excluded.
Dock status indicator2 steps
Steady white means powered on while the robot is away; slowly flashing white means emptying; steady red means the dust bag is missing; off means powered off or the robot is charging.
The power cord may exit either side.
Installation
Instructions from the manual
Prepare the cleaning area5 steps
Tidy cords, hard or sharp objects such as glass and nails and loose items.
Move unstable, fragile, precious or dangerous objects to avoid entanglement, collisions, injury and damage.
Use a physical security barrier in raised areas, including duplex apartments.
Follow the first full cleaning route and watch for problems.
Vacuum floors at least three times before the first mopping cycle.
Positioning the dock6 steps
Place the dock on a hard, flat floor against a wall.
Connect its cord and tidy excess cord.
Choose good WiFi coverage, plug in and confirm the status light is on.
Keep at least 0.5 m(1.6 ft)clearance on either side and 1.5 m(4.9 ft)in front; the diagram labels both clearances as more than these distances.
Avoid a vertically hanging cord, which could move or disconnect the dock.
Keep direct sunlight and obstructions away from its location beacon.
Attach the moisture-proof mat4 steps
Fix the dock, then wipe the mat location with a dry cloth.
Remove the double-sided adhesive backing and stick the mat to the floor.
Always use the mat on wooden floors; it sticks best to smooth surfaces.
Remove the tape slowly when necessary to reduce glue residue.
Powering on and charging5 steps
Before use remove the film from the dock locators at the robot front and rear.
Hold Power/Clean, wait for steady white and place the robot on the dock.
Keep its lithium-ion battery charged for performance.
If low battery prevents startup, place it on the dock.
It cannot be turned off while charging.
Starting mopping10 steps
Vacuum floors at least three times before the first cycle.
Remove the dustbin/water-tank combo unit, open the stopper, fill with tap water and replace the stopper.
Do not immerse the unit.
Dampen the mop cloth and wring until it stops dripping; fit it flat on the mount.
Align the positioning hole and fit the mount to the bottom of the combo unit.
Reinstall the unit in the robot.
Use cold water only; never rinse or immerse the combo unit.
Use no disinfectant and only Roborock-recommended solution.
Empty unused tank water immediately after mopping.
A small amount of factory-test water is normal.
Connecting to the app
Instructions from the manual
Connect to the Roborock app8 steps
Find Roborock in the App Store or Google Play, or scan the manual QR code and install it.
Turn on the robot.
Hold Power/Clean and Dock together for three seconds until the voice says Entering network configuration mode.
Slowly flashing white means the reset succeeded and it is waiting.
Open the app, tap Add Device or + and follow the current in-app guide.
Updates may change the process.
Only 2.4GHzWiFi is supported.
If router configuration, a forgotten password or another reason prevents connection, reset WiFi and add as a new device.
Disable WiFiView
Reset WiFi successfully, then wait five minutes for automatic deactivation. To reconnect, reset WiFi again.
Instructions for use
Instructions from the manual
Turn on and offView
Hold Power/Clean to switch on; the indicator lights and the robot waits for orders. Hold it to switch off and end the cycle. It cannot switch off while charging.
Start cleaning7 steps
Press Power/Clean.
The robot plans a route, outlines room edges, then fills each room in a zigzag pattern, room by room.
Before cleaning, tidy cords, including the dock cord, and valuables to prevent dragged items, disconnection or damage.
Install the mop cloth properly before each task.
Start from the dock and do not move the dock during cleaning.
Charge before starting if the battery is too low.
If low battery occurs during cleaning, it returns, charges and resumes.
Pause cleaningView
Press any button while running to pause. Press Power/Clean to resume, or Dock to send a paused robot to charge. Manually docking a paused robot ends the cleanup.
Auto-emptying3 steps
After cleaning the robot docks and emptying begins automatically.
If unused for a long period, empty the dustbin manually and clear its air inlet for good emptying performance.
Never operate without the dust bag installed or the dock cover closed.
Sleep3 steps
After more than ten minutes paused, the robot sleeps and the indicator flashes every few seconds.
Press any button to wake.
It does not sleep while charging and shuts down after more than twelve hours asleep.
Charging3 steps
The robot returns to charge after cleaning or when its battery is low during cleaning.
Press Dock to send a paused robot to charge; the indicator breathes during charging.
If it cannot find the dock, it returns to its starting position; place it on the dock manually.
Error indication4 steps
A fault makes the power indicator flash red.
An app pop-up appears and a voice alert may sound.
It sleeps after more than ten minutes malfunctioning.
Manually docking a malfunctioning robot ends the cleanup.
Do not disturb mode4 steps
Default DND is 22:00–08:00.
Change the period or disable it in the app.
In DND the robot does not play voice messages.
The Common Issues table separately says DND prevents auto top-up and auto-emptying.
Restore factory settings3 steps
If buttons do not respond or the robot cannot switch off, power on and hold Dock for five seconds.
After the voice message, hold Dock for five seconds again.
The robot restarts and restores factory settings, including scheduled cleaning and WiFi.
Routine maintenance
Instructions from the manual
Clean the main brush8 steps
Clean every two weeks and replace every 6–12 months.
Switch off and unplug before maintenance.
Turn over the robot and press the cover latches to remove the cover.
Remove and clean the main brush.
Reinstall the brush and cover and press the cover securely.
A wet cloth is recommended.
If soaked, air-dry away from direct sunlight.
Never use corrosive cleaner or disinfectant.
Clean the side brushView
Clean monthly and replace every 3–6 months. Switch off and unplug first. Unscrew the side-brush screw, remove and clean the brush, then reinstall it and tighten the screw.
Clean the robot sensorsView
Clean as required. Switch off and unplug first. Wipe the dock locator and all cliff sensors with a soft, dry cloth. Never use chemicals, cleaning fluids or sprays on these sensors.
Clean the omnidirectional wheel6 steps
Clean as required.
Switch off and unplug first.
Use a tool such as a small screwdriver to pry out the axle and remove the wheel.
Its bracket cannot be removed.
Rinse the wheel and axle to remove hair and dirt.
Air-dry, reinstall and press the wheel and axle back in place.
Clean the main wheelsView
Clean as required. Switch off and unplug first. Wipe with a soft, dry cloth.
Clean the dustbin and water tank combo unit7 steps
Clean as required.
Switch off and unplug first.
Press the release button and remove the unit.
Open its lid, empty and clean the dustbin.
Open the tank stopper and empty the tank, then reinstall the unit.
After mopping, empty the water tank, wash the cloth and air-dry them to prevent odors.
Never rinse or immerse the combo unit.
Clean the mop cloth3 steps
Clean after each use and replace every 3–6 months.
Switch off and unplug first.
Remove the mount in the direction shown in the reviewed diagram, remove the cloth, wash it and air-dry it.
Clean the washable filter6 steps
Clean every two weeks and replace every 6–12 months.
Switch off and unplug first.
Open the combo-unit lid, press its filter-holder latches and remove the holder.
Remove the filter, rinse repeatedly and tap out as much dirt as possible.
Allow at least 24 hours to dry thoroughly before reinstalling.
Never touch the surface with hands, brushes or sharp objects.
Maintain the auto-empty dock5 steps
Replace the dust bag when full for optimal performance.
Switch off and unplug first.
Open the cover, lift out and discard the bag.
Clean the filter with a dry cloth, install a new bag and close the cover.
Wipe the dock beacon and charging contacts with a soft, dry cloth.
Clean the charging contactsView
Clean as required. Switch off and unplug first. Wipe the robot and dock charging contacts with a soft, dry cloth.
Safety information
Instructions from the manual
Safety information26 steps
Use only the specified AED08HRR dock for recharging this 14.4 V/3200 mAh typical lithium-ion robot.
The manual also lists an alternative SPCDZ03RR station with its named regional supplies; that alternative is outside this auto-empty-dock reference.
Switch off and unplug before cleaning or maintenance.
Do not supply through a timer or regularly switched utility circuit: inadvertent thermal-cutout resetting is hazardous.
Follow the manual; improper-use loss or damage is borne by the user.
Do not use as a toy; supervise use by or near children.
Install the dustbin, washable filter, dust bag, side brush, mop cloth, main brush and cover before cleaning.
Do not clean hard or sharp objects such as decoration waste, glass or nails.
Never sit or stand on the robot or dock.
Use no disinfectant and only Roborock-recommended solution.
Keep low objects such as shoes and mats away from stairs.
Keep operating floors free of water.
Use barriers on elevated surfaces, including lofts, terraces, slides and furniture.
Keep hair, clothing, fingers and all human/pet body parts away from seams, openings and moving parts.
Never operate where an infant or child sleeps.
Do not carry by the vertical bumper, side brush or bumper.
Do not use the dock to collect stones, paper scraps or anything that blocks its air duct.
Never vacuum burning or smoking items, cigarettes, matches, hot ashes, flammable or explosive items such as lighters, gasoline or printer/copier toner.
Place the dock on a hard, flat floor away from fire and heat, including radiators.
Avoid humid, narrow or suspended locations.
Keep objects off the robot/dock and away from the dock suction inlet; never cover them.
Do not use without a dust bag.
Stop using damaged equipment and contact customer service.
Ventilate the operating area to avoid overheating.
Never rinse the robot or dock.
The manufacturer disclaims indirect, punitive, incidental and consequential damage arising from use, misuse or inability to use the product; this does not remove statutory rights that cannot lawfully be disclaimed.
Safe use and restrictions15 steps
Supervise children so they do not play with the appliance.
Under CB rules, people with reduced abilities or insufficient experience require instruction or supervision by someone responsible for safety.
Under EU rules, children aged eight or older and people with reduced abilities or insufficient experience may use it with safe-use instruction/supervision and understanding of hazards; children must not play or maintain it unsupervised.
Keep at least 20 cm between the device and people during operation; closer use is not recommended for RF compliance.
Do not co-locate its transmitting antenna with another antenna or transmitter.
Use only for indoor floor cleaning, never outdoors, on a sofa or other nonground surface, or in commercial/industrial environments.
Charge and discharge only at 4–40°C (39–104°F), avoiding high humidity.
Remove wires and unstable, fragile, valuable or dangerous objects before use.
Do not use on high-pile carpets; dark carpets may reduce effectiveness.
Never wipe charging contacts or the cord with wet wipes, damp cloths or wet hands.
Do not mop carpets.
Keep other appliance cords out of the cleaning area.
Never operate near an unattended infant/child or someone lying on the floor.
Keep lit candles and fragile floor objects out of the area; do not operate where furniture candles could be bumped.
Keep children off the robot/dock and watch for trip hazards.
Battery and charging
Instructions from the manual
Battery, storage and transport6 steps
Match supply voltage to the dock.
Use only supplied battery, charger, cord, dock and accessories to prevent smoke, heat or fire; do not use a power adapter for this supplied auto-empty configuration.
Dispose of batteries through a professional recycler.
Take protection measures against thunderstorms or unstable voltage.
For long storage, fully charge, unplug and switch off; store cool and dry and recharge at least every three months.
For transport unplug the dock, switch off the robot and empty tanks; original packaging is recommended.
Battery and cord service4 steps
Never charge nonrechargeable batteries.
Only skilled people may replace the batteries.
Do not dismantle, repair or modify the battery or dock.
Stop using a damaged cord immediately; the manufacturer, its service agent or a similarly qualified person must replace it to avoid hazards.
International symbols explanation
Instructions from the manual
Indoor-use symbolView
The house symbol means indoor use only.
Low power mode
Instructions from the manual
Low power modeView
While docked, hold Dock for ten seconds to activate Low Power mode. Press Dock until the LED brightens to deactivate it.
Eu declaration of
Instructions from the manual
EU conformity and network information2 steps
The manufacturer declares RRA0TCP compliant with Directive 2014/53/EU.
The compliance page named in the manual supplies the full declaration and network-interface, exposed-service and external-sensor information.
Eu declaration of conformity
Instructions from the manual
EU declarationView
Beijing Roborock Technology Co., Ltd. declares compliance with applicable directives, European norms and amendments; the manual identifies its compliance page for the full declaration.
Wifi specification
Instructions from the manual
WiFi specificationView
WiFi uses 802.11b/g/n in the 2400–2483.5 MHz range, with maximum output at or below 20 dBm.
Laser safety
Instructions from the manual
Laser safetyView
The distance sensor meets IEC 60825-1:2014 Class 1 laser-product requirements and does not generate hazardous laser radiation.
Weee information
Instructions from the manual
Product recycling3 steps
Do not dispose of this product with household waste in the EU.
Recycle responsibly to prevent environmental/human harm and support sustainable material reuse.
Use return/collection systems or contact the retailer for environmentally safe recycling.
Warranty information
Instructions from the manual
Warranty service4 steps
Warranty duration follows the sales-country law and is the seller’s responsibility.
It covers only material/workmanship defects.
Only an authorized service centre may make warranty repairs; supply the original purchase bill showing the date.
Exclusions include normal wear, misuse such as overloading, unapproved accessories or force, external damage, failure to follow the manual including unsuitable mains or installation, and partially/completely dismantled equipment.
A
Instructions from the manual
Product overview diagramsView
Use the complete robot, combo-unit, mop-module and auto-empty dock views with the paired Product Overview key.
B
Instructions from the manual
Installation diagramsView
Use the dock clearance, moisture-proof mat, power-on and mopping panels with the paired Installation instructions.
Complete dock clearance and moisture-proof mat placement panels. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
B: Installation.
B1: Position dock on hard, flat floor against wall; connect/tidy cord, choose good WiFi and check powered status. Avoid direct sun, obstructed beacon and vertically hanging cord.
B1-1: More than 1.5 m(4.9 ft)in front.
B1-2: More than 0.5 m(1.6 ft)on both sides; both repeated leaders retained.
B2: After fixing dock, clean mat location with dry cloth, peel tape and attach. Always use on wooden floors; best on smooth surfaces; remove tape slowly when needed.
Complete water filling, cloth fitting, mount alignment and combo-unit replacement sequence. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
B4: Starting mopping. Vacuum at least three times before first cycle.
B4-1: Remove combo unit, open stopper, fill with tap water and replace stopper; never immerse. Use cold water and only Roborock-recommended solution, no disinfectant.
B4-2: Dampen cloth, wring until no dripping and fit flat to mount; full cloth fitting arrows retained.
B4-3: Align positioning hole and fit mount into bottom of combo unit; all attachment arrows retained.
B4-4: Reinstall combo unit; full insertion arrow retained. Empty unused water immediately after mopping; factory-test residual water is normal.
C
Instructions from the manual
Routine maintenance diagramsView
Use the complete brush, sensor, wheel, combo-unit, mop-cloth and washable-filter panels with the paired Routine Maintenance instructions. Switch off and unplug before maintenance.
Complete main-brush removal/cleaning/refitting and side-brush removal panels. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
C: Routine maintenance; switch off and unplug first.
C1: Main brush: clean every two weeks and replace every 6–12 months.
C1-1: Turn over and press both cover latches to remove cover; complete lifting arrow and enlarged latch inset.
C1-2: Remove and clean the main brush; wiping with wet cloth recommended. If soaked, air-dry away from direct sun; no corrosive cleaner or disinfectant.
C1-3: Reinstall brush and cover and press securely; complete insertion arrows.
C2: Side brush: clean monthly and replace every 3–6 months. Unscrew, remove/clean, reinstall and tighten screw; complete screwdriver panel.
Complete front dock-locator and every repeated underside cliff-sensor wiping location. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
C3: Sensors: clean as required. Switch off and unplug first; use soft, dry cloth only, no chemicals or cleaning sprays.
C3-1: Dock locator; complete enlarged front inset retained.
C3-2: All cliff sensors; every repeated sensor location and wiping panel retained.
Complete combo-unit removal, dustbin cleaning, water emptying and replacement panels. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
C6: Combo unit: clean as required. Switch off and unplug first; never rinse or immerse it.
C6-1: Press release button and remove unit; full withdrawal arrow.
C6-2: Open lid, empty and clean dustbin; complete lid-opening and pouring panels.
C6-3: Open tank stopper and empty tank; full pouring panel.
C6-4: Reinstall unit; full insertion arrow. After mopping empty tank, wash cloth and air-dry to prevent odors.
Complete filter-holder removal, rinsing and at-least 24-hour drying panels. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
C8: Washable filter: clean every two weeks, replace every 6–12 months. Switch off and unplug first.
C8-1: Open combo-unit lid, press filter-holder latches and remove holder; full lifting arrow and holder view.
C8-2: Remove filter, rinse repeatedly and tap out dirt; full removal/rinsing panels. Never touch its surface with hands, brushes or sharp objects.
C8-3: Allow at least 24 hours to dry thoroughly before reinstalling.
Use the complete dust-bag, filter, beacon and charging-contact panels with the paired Routine Maintenance instructions. Switch off and unplug before maintenance.
Complete dust-bag replacement, dock-filter cleaning and beacon/contact wiping sequence. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
C9: Replace full bag for optimal emptying. Switch off and unplug first.
C9-1: Open cover, lift bag out and discard; entire cover/bag/arrow view retained.
C9-2: Clean filter with dry cloth; complete filter and bag compartment view retained.
C9-3: Fit new bag and close cover; full insertion arrow and cover retained.
C9-4: Wipe beacon and charging contacts with soft, dry cloth; both contact locations and wiping panel retained.
Controls and parts
See the manual diagrams 2 diagrams
Complete robot top and bottom views, control inset and all sensor/brush locations. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
A: Product overview.
A1: Robot top view; both top/rear views and enlarged control inset.
Power/Clean symbol: Hold to switch on/off; press to clean.
Dock symbol: Press to dock; any button pauses running.
A1-1: LiDAR sensor.
A1-2: Bumper.
A1-3: Dock locator.
A1-4: Charging contacts.
A2: Robot bottom view.
A2-1: Side brush.
A2-2: All cliff sensors; every repeated leader retained.
A2-3: Omnidirectional wheel.
A2-4: Main brush cover latches.
A2-5: Main brush.
A2-6: Both main wheels.
A2-7: Mop module.
Complete dock exterior, open-cover and rear cord-routing views. Q7 TF+ CE; base and FCC versions excluded.
Diagram key
A7: Auto-empty dock.
A7-1: Dock cover.
A7-2: Dustbin.
A7-3: Status light: steady white when powered and robot away; slowly flashing white while emptying; steady red for missing bag; off when unpowered or robot charging.
A8: Dock with top cover open.
A8-1: Disposable dust bag.
A8-2: All charging contacts.
A8-3: Dock location beacon.
A8-4: Suction inlet.
A9: Rear dock view.
A9-1: Power port.
A9-2: Power cord storage slot.
A9-3: Cord outlets; cord can exit either side.
Model details
Model and compatibility
Applicability
CE Q7 TF+ (Plus), RRA0TCP robot with AED08HRR 220–240V auto-empty dock. Base, FCC and alternative adapter-operated docks excluded.
Battery
14.4 V/3200 mAh typical lithium-ion battery; rated robot input 20 V DC, 0.8 A.
