MODEL REFERENCE

CASIO XJ-UT351W

16 errors · 16 troubleshooting topics · 62 guides

CASIO XJ-UT351W

The checks and guides below come from the official manuals for this model.

Errors and indicators

Light patterns and messages documented in the manual
Find the indicator lights
XJ-UT351W control panel and three indicator locations. Read state combinations together in the error list.
XJ-UT351W control panel and three indicator locations. Read state combinations together in the error list.

Diagram key

  • ENTER: Confirm a menu selection or execute a function.
  • AUTO: Automatically adjust RGB frequency and phase.
  • INPUT: Select the input source.
  • MENU: Open or close the settings menu.
  • ON/Stand-by power symbol: Switch projector power on or off.
  • POWER/STANDBY: Power and standby status indicator; colours and flashing combinations are given in the reviewed instructions.
  • LIGHT: Light-source indicator; interpret with POWER/STANDBY and TEMP.
  • TEMP: Temperature indicator; interpret with POWER/STANDBY and LIGHT.
  • ESC: Close a menu or cancel the current operation.
  • Four cursor keys: Navigate menus or change values; with no menu/dialog Up/Down opens keystone, then Up/Down adjusts vertical and Left/Right horizontal distortion. Left/Right adjusts light output with Light Control On.
  • Illuminance sensor: Ambient-brightness sensing when the Brightness Sensor setting is On.
内部が高温になっています。設置状況を確認してください。high internal temperature warning
2 checks

POWER is solid green; LIGHT and TEMP are unspecified. The interior is extremely hot.

Airflow or installation space insufficient
Check intake/exhaust are not blocked and clearances are sufficient (6 cm projection front, 30 cm others).
Dust on intake or exhaust vents
If vents are dusty, turn off and clean them using the reviewed cool/unplug cleaning procedure.
内部が高温になっています。電源をオフにします。high-temperature automatic shutdown
2 checks

POWER changes from solid green to solid red; LIGHT and TEMP are unspecified. Excessive internal temperature caused automatic shutdown.

Airflow or installation space insufficient
Check that intake/exhaust are unobstructed and clearances are sufficient (6 cm at the projection front and 30 cm at other sides).
Dust on intake or exhaust vents
  1. If the vents are dusty, clean them using the reviewed power-off, unplug and cool procedure.
  2. After both checks are clear, wait for POWER/STANDBY to become solid red and turn on again.
  3. If the error recurs, contact service/dealer.
POWER solid red; LIGHT solid red; TEMP solid redfan fault — all three indicators solid red
A fan fault caused automatic shutdown.Fan fault: Wait until POWER/STANDBY is solid red and the fan has stopped; unplug. Wait until indicators go out and for a while longer, reconnect and turn on. If error recurs contact service/dealer.
POWER solid red; LIGHT —; TEMP solid redsystem fault — POWER and TEMP solid red
A system fault caused automatic shutdown. LIGHT is unspecified in the source.System fault: Confirm POWER/STANDBY is solid red; wait for the fan to stop before unplugging. After indicators go out and a while longer, reconnect and turn on. If error recurs contact service/dealer.
POWER solid red; LIGHT —; TEMP solid redpossible external-noise fault — POWER and TEMP solid red
External noise or other interference may have caused automatic shutdown. This combination is also listed for a system fault; it does not uniquely identify the cause. LIGHT is unspecified in the source.Possible external-noise fault: Confirm POWER/STANDBY is solid red; wait for the fan to stop then unplug. After indicators go out and a while longer, reconnect and turn on. If error recurs contact service/dealer.
POWER solid red; LIGHT red flashing 0.5 s; TEMP red flashing 0.5 slight-source fault — red half-second blinking
The light went out or failed to light, causing automatic shutdown. Both red flashing cycles are approximately 0.5 seconds.Light-source fault: Confirm POWER/STANDBY is solid red; wait for the fan to stop then unplug. Wait a while, reconnect and turn on. If error recurs contact service/dealer.
POWER solid red; LIGHT off or red flashing; TEMP red flashing 2 sinternal memory fault — TEMP red two-second blinking
An internal memory error caused automatic shutdown. TEMP flashes red at approximately 2-second cycles; the LIGHT flashing interval is not specified.Internal memory fault: Confirm POWER/STANDBY is solid red; wait for the fan to stop then unplug. After indicators go out and a while longer, reconnect and turn on. If error recurs contact service/dealer.
ID-01firmware file-format problem
There is a problem with the file format. Re-download the exact projector’s firmware from official support and repeat the update procedure.Related instructions: Connect for firmware or user-logo transfer · Check firmware version and update requirements · Install the firmware USB driver
ID-02no firmware USB connection
3 checks
USB driver not installed
Confirm the driver has been installed.
USB connection incorrect
Confirm the PC and projector are correctly connected.
Projector not powered on
Confirm projector power is on.
ID-03firmware version is not newer
This is not a new ROM version. The attempted firmware is the same or older than the installed version; install newer firmware data.Related instructions: Connect for firmware or user-logo transfer · Check firmware version and update requirements · Install the firmware USB driver
ID-04firmware belongs to another model
This ROM data is for a different model. Use the correct exact-model firmware data.Related instructions: Connect for firmware or user-logo transfer · Check firmware version and update requirements · Install the firmware USB driver
ID-01lOGO Loader ID-01 — There is a problem with the file format.
The logo header may be faulty. Download the exact-model header again and repeat the complete transfer.
ID-02lOGO Loader ID-02 — A connection could not be established with the projector. Check the USB cable connection, turn the projector off and then back on, and then try again.
Check that the USB driver is installed, the USB cable correctly joins computer and projector, and projector power is on.
ID-04lOGO Loader ID-04 — This logo header file is for a different model.
Download the header for this exact model and repeat the complete transfer.
ID-05lOGO Loader ID-05 — The logo data was too large to transfer. Reduce the image size and try again.
Use image pixel dimensions 640×480 through 1280×800 as specified.
ID-06lOGO Loader ID-06 — This type of image file is not supported.
Use the specified RGB 24-bit full-colour BMP image format.

Troubleshooting

Find the problem you are experiencing
Missing picture dotsView

Manual section: その他のご注意 (PDF page 14).

Some unlit dots may occur despite precision manufacturing; the manual says this is not a fault.
Image discolouration after impact4 steps

Manual section: その他のご注意 (PDF page 14).

  1. Avoid impact during projection.
  2. If an impact interrupts or discolours the image, use INPUT to reselect the previous source.
  3. If colour does not recover, turn off and on.
  4. For an error follow the reviewed error-indicator table.
Blur after condensationView

Manual section: 使用上のご注意 (PDF page 11).

Cold-to-warm movement or rapid room heating can cause condensation and blur or faults. Turn off, leave it for a while, then turn on again. No fixed waiting time is specified.
Power will not turn on2 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

POWER/STANDBY not lit
Connect the power cord correctly.
TEMP or LIGHT stays lit/blinking
Consult the reviewed error-indicator table.
No picture or abnormal picture3 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

Source equipment off or no video
Check the connected computer/video equipment is powered and operating normally.
Wrong input selected
Select the input matching the connected device.
Component output not compatible through COMPUTER IN 1/2
Try the projector VIDEO or S-VIDEO input instead.
Extreme colour or display displacement1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

COMPUTER IN signal mode does not match RGB/component source
Set Input Settings > COMPUTER IN 1 or 2 Terminal to Auto instead of the incorrect forced RGB or Component mode.
Restore Japanese menu language1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

Menu language changed
MENU; for HDMI-PC press Down 4 times, otherwise Down 5 times; ENTER. Press Up twice, ENTER. Use Up/Down to select 日本語, ENTER; MENU closes.
No sound4 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

Projector volume low or muted
Adjust with VOLUME+ or VOLUME−.
Source volume low or absent
Adjust the connected source volume.
Wrong audio port connection/assignment
Check the audio output connection to the assigned input using the reviewed audio-input guide.
Audio Output is Line
Set Device Settings 2 > Audio Output to Speaker.
Incorrect picture colours3 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

Brightness mismatch
FUNC > Brightness; adjust.
Colour mode mismatch
FUNC > Colour Mode; change it.
Colour balance mismatch
Adjust Image Adjustment 1 > Colour Balance.
Blurred text3 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

Focus not adjusted
Adjust the focus lever.
RGB frequency or phase mismatch
For RGB only press AUTO.
RGB still requires manual adjustment
For RGB only adjust Image Adjustment 2 > Frequency and Phase.
Cannot pass the password prompt1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

Power On Password enabled
Enter the correct password and ENTER. If remote keys cannot enter it, follow the remote control checks.
Remote control does not work3 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

Batteries exhausted
Replace remote batteries.
Outside range
Operate within approximately 5 m.
IDs mismatch
Match remote/projector IDs or set one ID to All.
TEMP or LIGHT stays lit or blinking1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

An error has occurred
Consult the reviewed error-indicator table.
Light-source unit does not light2 checks

Manual section: 本機のトラブルと対処について (PDF page 45).

BLANK temporarily switched light off
Press BLANK or ESC.
Light-source unit end of life or faulty
Ask service/dealer for replacement; do not perform internal repair.
Unexpected shutdown and restart1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

Automatic self-check restart
Rare automatic self-check restart is not a fault; continue use. If repeated continuously contact service/dealer.
General abnormal operation recovery1 check

Manual section: 本機のトラブルと対処について (PDF page 45).

An abnormality may clear after the stated reset
Wait for the fan to stop after an error, unplug and leave at least 10 minutes. Reconnect and turn on. If not restored contact service/dealer.

Guides

安全上のご注意

Instructions from the manual
Stop for smoke, unusual smell or abnormal heat3 steps
  1. Use adult supervision if children can approach or touch the projector.
  2. If smoke, unusual smell or abnormal heat occurs, stop using it: continuing risks fire or electric shock.
  3. Unplug the power plug immediately, then contact the repair enquiry service or dealer.
Stop for faults, liquid ingress or damage7 steps
  1. Do not continue use with abnormal operation or an abnormal image.
  2. Turn off, unplug, then contact the repair enquiry service or dealer.
  3. If water, liquid or metal/other foreign matter enters, or the projector is dropped or damaged, turn off, unplug, then contact service/dealer.
  4. Keep water and liquid containers away.
  5. Do not open, dismantle or modify the cabinet: high voltage can cause shock, burns or injury and voids warranty/repair eligibility.
  6. Internal inspection, adjustment and repair belong to service/dealer.
  7. Never throw the projector into fire.
Safe placement, ventilation and projection light15 steps
  1. Use a firm flat stable surface; lock cart wheels.
  2. Keep at least 6 cm between the projection-facing front and screen/wall and 30 cm at all other sides.
  3. Keep the space between projector and screen empty and leave intake/exhaust unobstructed.
  4. Do not enclose it, cover it, place it on soft carpet/bedding/towels/soft seats, or use it standing vertically.
  5. Operate at 5–35°C.
  6. Avoid vibration, damp, dust, kitchen fumes, heaters, heated carpets, direct sun and extreme temperatures.
  7. Do not place it in a bathroom/wet area, on an unstable stand or high shelf, load it or stand on it.
  8. Do not look into the illuminated lens, intake or exhaust.
  9. Before switching on check nobody is looking into them; supervise children.
  10. Do not place magnifiers, mirrors, aquariums, refracting/reflecting objects or anything blocking the projection beam in its path.
  11. Do not touch the lens.
  12. Do not touch the hot exhaust or place heat-sensitive plastic near or below it.
  13. Do not open the cabinet.
  14. Do not use flammable-gas sprays inside or around it.
  15. During lightning do not touch the power plug.

電源コードについて

Instructions from the manual
Japan-only electrical and model scope9 steps
  1. Use this Japan-domestic unit only in Japan, on 100 V AC 50/60 Hz.
  2. Use only its supplied power cord, never with another appliance.
  3. Connect earth before plugging into a grounded 100 V outlet; disconnect earth only after unplugging.
  4. Keep the plug accessible.
  5. Do not overload or share the outlet with other appliances.
  6. Observe extension-cord ampere ratings.
  7. Do not bundle, heat, load, modify, damage, trap, cover with a rug, forcibly bend, twist or pull the cord.
  8. Keep it away from heaters; never touch cord or plug with wet hands.
  9. When away, keep pets away from the product and unplug: chewing can short the cord and cause fire.
Care for the power cord and move safely8 steps
  1. Insert the plug fully.
  2. After use and during long non-use unplug by holding the plug, never pulling the cord.
  3. Turn off and remove the cord before moving.
  4. At least yearly unplug and remove dust from plug blades and surroundings using a dry cloth or vacuum.
  5. Do not use detergent on the cord, especially the plug.
  6. During and immediately after operation the exhaust is hot.
  7. Carry by the two sides shown in the source movement figure, avoiding the exhaust.
  8. Keep important stored settings in a separate written record because malfunction/repair may erase them.

電池について

Instructions from the manual
Remote and battery safety7 steps
  1. Use the specified two AAA alkaline batteries with correct polarity.
  2. Do not disassemble, short, heat, burn or recharge batteries; do not mix old/new batteries or different types.
  3. Remove exhausted batteries promptly and remove batteries for long non-use.
  4. Dispose under local rules.
  5. For alkaline-battery liquid in an eye, do not rub: rinse immediately with clean water and obtain medical treatment immediately; untreated exposure can cause blindness.
  6. Do not dismantle or modify the remote or expose it to water; ask service/dealer for inspection or repair.
  7. Replace its batteries at least yearly regardless of use and do not store with keys held down.

磁石について

Instructions from the manual
Magnets, internal cleaning and disposal6 steps
  1. The projector contains magnets.
  2. Keep it away from pacemakers and other medical electrical equipment.
  3. If an abnormality is felt, move away immediately and consult a doctor.
  4. Keep magnetic cards, tapes, disks, prepaid cards and tickets away to avoid erased recordings.
  5. Arrange paid internal cleaning with service/dealer at least once a year, preferably before the humid rainy season: dust can reduce brightness or cause fire/failure.
  6. Do not dismantle it for disposal; follow local rules.

光源ユニットについて

Instructions from the manual
Light-source life and laser precautions8 steps
  1. Laser/LED light-source life is approximately 20,000 hours depending on individual unit, conditions and settings; it is not a guarantee.
  2. Light-source warranty ends at the earlier of the product warranty period or 6,000 hours.
  3. If the light no longer lights or becomes markedly dim, ask service/dealer for replacement.
  4. Never dismantle or modify it.
  5. Do not stare into the light and supervise small children.
  6. The non-USA label is Class 1 under IEC 60825-1:2014; the separate USA label is Class 2 under IEC 60825-1:2007 and does not authorize overseas use of the Japan unit.
  7. Do not use adjustments or procedures outside the manual.
  8. The exhaust is hot during projection; do not touch or obstruct it or insert foreign objects.

その他のご注意

Instructions from the manual
Storage and image-quality precautions7 steps
  1. Avoid static, extreme temperature, humidity, rapid temperature change, dust, unstable/tilted surfaces, water, oil/smoke, salt damage and corrosive gases.
  2. Keep strong fluorescent light and sunlight off the remote receiver.
  3. Do not trap a hand beneath the projector during installation or underside adjustments.
  4. Keystone correction compresses the picture and may lower quality.
  5. Place it as squarely as possible to the screen; if picture quality matters use a placement needing no correction and cancel correction.
  6. Continuous 24-hour operation or ignoring installation requirements may incur paid repair even within warranty.
  7. High heat, dust, oil/tobacco smoke can shorten optical-engine replacement intervals; ask service about timing and cost.

内容物のご確認

Instructions from the manual
Check the supplied items2 steps
  1. Package: projector, YT-160 remote, two trial AAA batteries, power cord, cable cover, safety notes, before-use notes and warranty.
  2. YT-131 belongs to XJ-UT351WN and does not define this model’s supplied remote.

投映までの操作の流れ

Instructions from the manual
Initial setup and shutdown12 steps
  1. Insert the supplied two AAA alkaline batteries in the remote with the illustrated polarity.
  2. Place the projector on a firm table or stand with adequate clearance; read the safety/use/placement precautions.
  3. For wall mounting purchase its dedicated bracket and consult the dealer.
  4. Adjust its installation angle.
  5. Connect the supplied cord to AC inlet and specified outlet.
  6. Connect the source video/audio equipment and turn those devices on.
  7. Press the power key.
  8. On first use select the language in the initial-language screen.
  9. Press INPUT and choose the source.
  10. Use the focus lever to focus.
  11. Adjust keystone and light output if needed.
  12. To finish press the power key to turn off.

各部の名称

Instructions from the manual
Identify parts, controls and model-specific ports6 steps
  1. Exterior: illuminance sensor, control panel, indicators, power key, left exhaust, two intakes, AC inlet, remote receiver, terminal area, focus lever, security bar, Kensington-compatible lock hole and projection lens.
  2. Body controls: MENU, ENTER, AUTO, INPUT, power, ESC and four cursors.
  3. Indicators: POWER/STANDBY, LIGHT, TEMP.
  4. Focus is manual via the lever; the lens has fixed zoom.
  5. XJ-UT351W ports: DC 5 V/2 A power-only Type A, LOGO Micro-USB Type B, HDMI 1/2, AUDIO IN 1/2, MONITOR OUT, COMPUTER IN 1/2, MIC, AUDIO OUT, AUDIO IN R/L, VIDEO, S-VIDEO and SERIAL.
  6. No LAN or USB host/media input applies.

設置する

Instructions from the manual
Place projector and adjust its feet6 steps
  1. Use a firm table or stand with ample clearance, lens centered and projector perpendicular to the screen.
  2. Use the test pattern to check size, tilt and other adjustments.
  3. Turn the one front underside adjustment foot to fine-tune elevation.
  4. Turn the two rear underside feet to fine-tune side-to-side tilt.
  5. Keep the plug accessible, 6 cm at the projection front and 30 cm elsewhere.
  6. If exhaust heat blown toward the lens by air-conditioning causes image shimmer, change air flow direction or projector location.
Front and rear foot adjustments with both numbered callouts and all rotation arrows.
Front and rear foot adjustments with both numbered callouts and all rotation arrows.

Diagram key

  • 1: Turn the one front underside adjustment foot to fine-tune elevation. Both rotation directions are retained.
  • 2: Turn the two rear underside adjustment feet to fine-tune side-to-side tilt. Both foot positions and all rotation arrows are retained.

外部機器との接続

Instructions from the manual
Connect video and audio source devices11 steps
  1. Connect before projection using cables matching both device terminals; cables not supplied must be obtained separately.
  2. Multiple video sources may be connected; select with INPUT.
  3. Computer RGB or component video uses COMPUTER IN 1/2 mini D-sub 15 via an RGB or component cable.
  4. S-video uses S-VIDEO mini DIN 4; composite uses VIDEO RCA.
  5. HDMI equipment uses HDMI 1/2 with High Speed HDMI cable.
  6. Analogue audio uses AUDIO IN 1/2 stereo mini or AUDIO IN R/L RCA.
  7. MIC accepts a microphone but does not support plug-in-power microphones.
  8. External analogue RGB display uses MONITOR OUT and RGB cable.
  9. External speakers use AUDIO OUT and an audio cable; set Device Settings 2 > Audio Output to Line.
  10. DC 5 V is power only.
  11. RS-232 C uses SERIAL and cross serial cable.

ケーブルカバーの取り付けと取り外し

Instructions from the manual
Attach and remove the cable cover5 steps
  1. Turn off, unplug and wait for the projector to cool before attaching or removing the cover.
  2. Attachment: turn the projector over; insert cover hooks into body hook holes (Figure 1).
  3. Rotate the cover in Figure 2’s direction onto the body.
  4. Align cover screw with body screw receiver (Figure 3) and tighten with a Phillips screwdriver (Figure 4).
  5. Removal: loosen the cover screw with a Phillips screwdriver and detach it from the body; separate the cover screw side from the body, then withdraw the hooks.
Complete four-figure cable-cover sequence. Turn off, unplug and let the projector cool before attaching or removing the cover.
Complete four-figure cable-cover sequence. Turn off, unplug and let the projector cool before attaching or removing the cover.

Diagram key

  • Figure 1 screw: Cover screw, aligned with the body receiver in Figure 3.
  • Figure 1 hooks: Insert the cover hooks into the body hook holes. The complete enlarged inset retains its insertion arrow and both ends of the callout.
  • Figure 2 rotation arrow: Rotate the cover onto the body in this direction after inserting the hooks.
  • Figure 3 screw: Align the same cover screw with its receiver.
  • Figure 3 screw receiver: Body receiver for the cover screw.
  • Figure 4 arrow: Tighten with a Phillips screwdriver. Removal: loosen and detach the screw, separate the screw side, then withdraw the hooks.

リモコンについて

Instructions from the manual
Use the supplied YT-160 remote5 steps
  1. Aim the emitter at a projector remote receiver from within approximately 5 m.
  2. Avoid holding keys down in storage, because this drains batteries.
  3. Grouped controls: emitter, power, ESC, ID buttons 1–4, cursor Up/Down/Left/Right and ENTER, function keys.
  4. Power toggles on/off; ESC exits/cancels; cursor keys navigate or change values; ENTER confirms/executes.
  5. Network-only playback keys are not part of this model’s functions.

基本操作一覧

Instructions from the manual
Select the input source7 steps
  1. Press INPUT; use INPUT or Up/Down to select the desired source; press ENTER.
  2. Without ENTER the source switches after approximately 3 seconds.
  3. The source name shows briefly in the upper right.
  4. If no signal is detected, 「入力信号がありません」 appears.
  5. Choose Computer 1/2 RGB or component, Video, S-Video, HDMI 1 or HDMI 2.
  6. Computer 1 defaults to AUDIO IN 1, Computer 2 to AUDIO IN 2, Video/S-Video to AUDIO IN R/L, and HDMI 1/2 to its own audio.
  7. File Viewer, CASIO USB Tool and Network do not apply.
Manually correct keystone distortion4 steps
  1. With no onscreen menu/dialog press body Up/Down or remote KEYSTONE+/−.
  2. Use Up/Down for vertical and Left/Right for horizontal correction.
  3. Both adjust within±5 degrees.
  4. Press ESC to finish.
Enlarge and pan part of the imageView
Press D-ZOOM+ to enlarge the image centre. Use D-ZOOM+ to increase or D-ZOOM− to reduce magnification. Use Up/Down/Left/Right to pan the enlarged image. Press ESC to finish.
Temporarily blank picture and sound4 steps
  1. Press BLANK to interrupt picture and sound and show the configured Blank Screen.
  2. If Black is selected, the projection light turns off.
  3. Auto Power Off is disabled until blank is cancelled.
  4. Press BLANK or ESC to restore; the power key also restores only when the Blank Screen setting is Black.
Freeze the pictureView
Press FREEZE to hold the current frame. Press FREEZE or ESC to return to live source video.
Automatically adjust RGB videoView
During RGB projection press AUTO to automatically adjust frequency and phase, which may reduce flicker. This does not apply to other inputs.
Choose an aspect ratio6 steps
  1. Press ASPECT repeatedly.
  2. WXGA Computer RGB/HDMI-PC cycles Standard, Full, 16:9, 4:3, Real; Video, S-Video, Component/HDMI-DTV cycles Standard, 16:9, 16:10, 4:3, Letterbox.
  3. Standard preserves aspect at maximum fit; Full stretches to maximum size.16:9 corrects 16:9 squeezed into 4:3; 16:10 fits a 16:10 screen; 4:3 forces 4:3.
  4. Real maps one input dot to one output pixel, cropping excess resolution; RGB below SVGA is enlarged to SVGA.
  5. Letterbox preserves ratio, resizes width to 1280 dots and projects the central 800 rows.
  6. Public/commercial screen resizing may infringe copyright.
Select a colour mode3 steps
  1. Press FUNC, select Colour Mode, ENTER; choose with Up/Down and ENTER.
  2. Colour mode cannot be selected when Light Control is Off.
  3. Choices: Standard (default for PC), Graphics, Theater (default for S-Video, Video, Component, HDMI-DTV), Blackboard, Natural.
Adjust volume or muteView
Press VOLUME+ or− to open the volume dialog; use+ to raise or− to lower. To mute, open the volume dialog and press ENTER. Restore audio with VOLUME+ or−.

入力ソースについて

Instructions from the manual
Match computer resolution to the projector2 steps
  1. If images are rough, text unclear or moiré appears, set computer output to the native WXGA 1280×800 of XJ-UT351W following the computer instructions.
  2. Alternatively select Real aspect on this WXGA model for pixel-mapped projection.

ライトコントロール

Instructions from the manual
Adjust light output and brightness sensing5 steps
  1. Light Control On (default) allows seven output levels 1–7.
  2. With no menu/dialog press Left/Right to show the current level and use Left/Right to adjust; ESC finishes.
  3. MENU > Device Settings 1 > Light Control > Brightness Sensor On enables ambient-light adjustment; default Off.
  4. For maximum source brightness set Light Control Off, which disables level adjustment and sensing.
  5. Light Control Off Mode offers Bright (brightness priority) or Normal (default, colour priority).

デジタルスクリーンシフト

Instructions from the manual
Change or reset digital screen shift5 steps
  1. MENU > Screen Settings > Digital Screen Shift > Change Digital Screen Shift, ENTER.
  2. Use D-ZOOM−/+ to resize 84–100 percent.
  3. Below 100 percent use Up/Down to move vertically and Left/Right horizontally; at 100 percent skip movement.
  4. ESC closes the dialog; MENU closes the settings.
  5. To reset: MENU > Screen Settings > Digital Screen Shift > Reset Digital Screen Shift, ENTER; Up selects Yes, then ENTER.

テストパターンの投映

Instructions from the manual
Project a test pattern4 steps
  1. MENU > Screen Settings > No Signal Screen or Blank Screen; use Left/Right to select Test Pattern; MENU closes.
  2. For No Signal Screen choose an input with no signal using INPUT; for Blank Screen press BLANK.
  3. Use for position, size, keystone, focus, aspect and digital screen shift adjustments after wall installation.
  4. Auto Power Off is disabled while test pattern is projected.

音声入力の変更

Instructions from the manual
Assign or reset audio inputs5 steps
  1. MENU > Device Settings 2 > Audio Input, ENTER; choose the source with Up/Down; use Left/Right to assign its audio input.
  2. Repeat for other sources as needed, then MENU closes.
  3. AUDIO IN 1, AUDIO IN 2 or AUDIO IN R/L may replace the default assignment.
  4. To reset all assignments, run Device Settings 2 > Initialize Device Settings 2.
  5. This resets ALL settings in Device Settings 2, not just audio.

操作パネルロック

Instructions from the manual
Lock or unlock the body controls4 steps
  1. To enable: MENU > Device Settings 2 > Control Panel Lock; Left selects On; ENTER confirms the dialog; MENU closes.
  2. All body keys except power are locked; remote control still works.
  3. To unlock with body keys: with no menu/dialog hold Down until the unlock message appears, then release.
  4. Or use the remote in the above menu path, Right selects Off, then MENU.

リモコンidとプロジェクターidの設定

Instructions from the manual
Set and inspect remote and projector IDs6 steps
  1. IDs 1–4 avoid cross control for up to four nearby projectors.
  2. Both default All, which communicates regardless of other ID.
  3. Matching IDs or All are necessary for all normal remote operations.
  4. Remote only, even with projector off: hold ESC and press 1, 2, 3 or 4 to set that remote ID; ESC+MENU sets All.
  5. During projection set projector ID: MENU > Device Settings 1 > Projector ID, ENTER; Up/Down chooses 1–4 or All; ENTER.
  6. Hold ESC and press INPUT to display both IDs for approximately 10 seconds, even when IDs conflict.

プレゼンテーションタイマーを使う（timer）

Instructions from the manual
Configure the presentation countdown8 steps
  1. With no timer displayed, press TIMER once to show it.
  2. With Continuous Display Off it disappears after about 5 seconds.
  3. To open timer functions, press TIMER twice if hidden or once if visible.
  4. Use Up/Down to select Display Position, Continuous Display or Set Time; Left/Right change selection.
  5. Position: bottom right (default), top right, top left, bottom left.
  6. Continuous Off (default) hides after 5 seconds; On keeps it until another dialog or ESC.
  7. Set Time is 5–60 minutes in 5-minute increments (default 20 minutes).
  8. ESC saves and closes; to immediately start choose Start Timer and ENTER before ESC.

計時の各種操作

Instructions from the manual
Start, pause, resume or reset the timer4 steps
  1. Open the timer functions menu.
  2. Select Start Timer and ENTER to start countdown and close the menu.
  3. At 00:00 it counts up in red for 60 minutes from−00:01 to−60:00.
  4. Select Pause Timer and ENTER to pause; Resume Timer and ENTER to resume; Reset Timer and ENTER to return to the configured countdown time.

設定メニュー項目一覧

Instructions from the manual
Use settings and adjust picture quality10 steps
  1. Press MENU to open/close Settings.
  2. Asterisk marks defaults.
  3. R=RGB, C=Component, V=S-Video/Video, H=HDMI-PC, D=HDMI-DTV; items apply only to indicated sources.
  4. N-marked network items and F/T/Network inputs are inapplicable.
  5. Image Adjustment 1: Brightness, Contrast; V-only Sharpness (higher sharper), Colour Saturation (higher richer) and Tint (higher bluer, lower redder; NTSC/NTSC 4.43 only).
  6. Colour Balance offers Warm, Standard (default), Cool and individual RGB adjustments.
  7. Image Adjustment 2: Vertical/Horizontal Position for RGB/Component/Video; Frequency for RGB vertical bands, Phase for RGB flicker.
  8. If manual frequency makes RGB disappear, press AUTO.
  9. Overscan for Component/Video/HDMI-DTV is 0–5 percent (default 5); lower values display more of the input.
  10. Initialize Image Adjustment 1/2 or Volume Adjustment resets all items in that group for the current source.
Screen and projection settings9 steps
  1. Screen Settings vertical/horizontal keystone correct distortion.
  2. Correction Priority Shape reduces keystone-related distortion but slightly narrows projection; Size (default) keeps normal area but may distort.
  3. Aspect and Digital Screen Shift use the reviewed guides.
  4. Projection Method Front (default) projects from in front; Rear horizontally mirrors for rear projection.
  5. Ceiling Projection On is for upside-down wall mounting and flips both axes; Off (default) is for table top.
  6. No Signal Screen choices Blue (default), Black, Logo (built-in or user logo), Test Pattern.
  7. Blank Screen has the same choices with Black default.
  8. Test Pattern disables Auto Power Off.
  9. Initialize Screen Settings resets all current-source screen items.
Input signal and automatic adjustment settings6 steps
  1. Input Settings > COMPUTER 1/2 Terminal: Auto (default) detects RGB/Component; RGB or Component forces that interpretation.
  2. RGB 1/2 Level Adjustment On (default) usually optimizes RGB; if image is disturbed change to Off.
  3. Video/S-Video Signal: Auto (default) or NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL 60, SECAM.
  4. Signal Name Display On (default) shows input name after INPUT selection; Off hides it.
  5. Initialize Input Settings resets current-source input items.
  6. Device Settings 1 > Auto Adjustment On (default) detects RGB resolution/frequency and adjusts; Off preserves manual vertical/horizontal position, frequency and phase across power cycles.
Power, language and device settings11 steps
  1. Auto Power Off acts after both no key activity and no input for 5, 10 (default), 15, 20 or 30 minutes; Off disables it.
  2. Direct Power On set to On starts upon connecting mains; default Off.
  3. Device Settings 1 > Language selects English, French, German, Italian, Spanish, Swedish, Portuguese, Dutch, Norwegian, Polish, Finnish, Czech, Turkish, Russian, Lithuanian, Vietnamese, Thai, Malay, Indonesian, Arabic, Simplified Chinese, Traditional Chinese, Korean or Japanese.
  4. Initialize Device Settings 1 resets all current-source items in that group.
  5. Device Settings 2 > Audio Output: Speaker (default) or Line (AUDIO OUT).
  6. High Altitude On for 1500–3000 m improves fan cooling; Off (default) below 1500 m.
  7. Never use above 3000 m.
  8. Closed Captions for Video with captions: Off (default), CC 1, CC 2, CC 3, CC 4.
  9. Timer Function opens timer functions.
  10. Microphone Input Level 0 (default, mute)–3 (maximum).
  11. Initialize Device Settings 2 resets all current-source items in that group.
Enable standby RGB and audio output4 steps
  1. Device Settings 2 > Standby RGB/Audio: Output enables MONITOR OUT and AUDIO OUT while powered but in standby; Do Not Output is default.
  2. Standby video is only COMPUTER IN 1; audio is that assigned to Computer 1 plus MIC.
  3. Standby audio always uses AUDIO OUT regardless of Audio Output Speaker/Line.
  4. COMPUTER IN 2 video cannot output during standby.
Inspect information and initialize settings4 steps
  1. Information lists input signal, signal name, resolution, horizontal/vertical frequency, scanning method, audio input, projector ID, light use time and Version (ROM version).
  2. Unit Use Time is cumulative and cannot be reset.
  3. All Initialization resets Settings except Language, Password, Light Use Time, Version and Unit Use Time.
  4. Transferred user logo is not erased.

パスワード機能の利用

Instructions from the manual
Change or enable the power-on password14 steps
  1. Password protection discourages unauthorized use but does not prevent theft.
  2. Keep the remote, replace weak batteries and match IDs or set either to All.
  3. Record the password separately and change the factory password promptly.
  4. MENU > Device Settings 1 > Password, ENTER.
  5. Enter current password then ENTER.
  6. Factory sequence: Up, Down, Left, Right, Up, Down, Left, Right.
  7. Down selects Change Password, ENTER.
  8. Enter up to eight key operations, ENTER; re-enter the same password, ENTER.
  9. On registered message press ESC.
  10. If mismatch message appears, ESC and retry the new password entry.
  11. Permitted keys: INPUT, MENU, BLANK, FREEZE, the printed light-control key, VOLUME+/−, D-ZOOM+/−, KEYSTONE+/−, four cursors, TIMER, AUTO, ASPECT, FUNC.
  12. To enable/disable, repeat the current-password menu steps; with Power On Password selected use Left/Right to choose On/Off.
  13. When Off→On, ENTER confirms asking at power-on or ESC cancels.
  14. MENU closes.

ご自分のパスワードを忘れてしまった場合には

Instructions from the manual
Forgotten password service procedure2 steps
  1. Take projector and identification (employee ID, driving licence, etc.; copy accepted) to the repair enquiry service and request paid password removal.
  2. This resets all settings except light use time.

本機外部のクリーニング

Instructions from the manual
Clean the projector exterior3 steps
  1. Turn off, unplug and allow it to cool fully before cleaning.
  2. Wipe the exterior using a soft cloth dampened with diluted neutral detergent and wrung out firmly.
  3. Never use benzine, alcohol, thinner or other chemicals.

レンズのクリーニング

Instructions from the manual
Clean the projection lensView
Turn off, unplug and allow it to cool fully. Wipe with commercial spectacle-cleaning cloth or lens cleaning paper. Do not apply excessive force or scratch the lens.

吸気口などのクリーニング

Instructions from the manual
Vacuum intake and exhaust vents4 steps
  1. Turn off, unplug and allow it to cool fully.
  2. Carefully vacuum dust from both illustrated intakes approximately monthly.
  3. Dust can overheat the interior and cause failure.
  4. Depending on environment dust may also accumulate on the exhaust; clean it in the same way.
Both intake-cleaning locations with complete vacuum nozzles and dust-removal arrows.
Both intake-cleaning locations with complete vacuum nozzles and dust-removal arrows.

Diagram key

  • Left nozzle and arrows: Carefully vacuum the first illustrated intake approximately monthly.
  • Right nozzle and arrows: Carefully vacuum the second illustrated intake approximately monthly. Turn off, unplug and cool fully before cleaning; treat dusty exhaust in the same way.

インジケーター表示について

Instructions from the manual
Read normal indicator combinations9 steps
  1. Read POWER/STANDBY, LIGHT, TEMP together: solid red/solid orange/solid orange immediately after connection; wait for standby before turning on.
  2. Solid red/off/off is standby.
  3. Blinking green/solid orange/solid orange is warm-up.
  4. Solid green/off/off is ready with Light Control Off; solid green/solid green/off is ready with Light Control On.
  5. Blinking red/off/off is internal processing just after shutdown.
  6. Solid dot means lit, double circle blinking, open circle off.
  7. Error-table em-dash means unspecified, not a guessed off state.
  8. Before unplugging after an error wait for the fan to stop, otherwise it may not recover at reconnection.
  9. ESC dismisses warning messages.

外部機器への給電について

Instructions from the manual
Supply power to an external USB device7 steps
  1. DC 5 V/2 A Type A on XJ-UT351W is a power-only terminal, not USB host.
  2. Before powering an external device set Device Settings 1 > Auto Power Off to Off.
  3. Shutdown, self-check restart, Auto Power Off or error stops power and may erase/damage unsaved external data; save often.
  4. Use CASIO-tested devices where possible; other devices up to DC 5 V/2 A may work with limited functions and are not guaranteed.
  5. Follow the external device instructions, especially for rechargeable batteries: wrong connection risks rupture, smoke or fire.
  6. CASIO disclaims responsibility for connected device/data failures.
  7. To interrupt projection while continuing supply press BLANK.

ファームウェア更新、ユーザーロゴ転送について

Instructions from the manual
Connect for firmware or user-logo transfer2 steps
  1. Connect the computer USB port to the projector LOGO Micro-USB Type B terminal using a commercial matching cable.
  2. Follow the complete separate firmware or user-logo transfer guide; do not use DC 5 V as a data-input port.
Related instructions: Check firmware version and update requirements · Install the firmware USB driver · Update the projector firmware

本機を壁に設置する

Instructions from the manual
Wall-installation precautions5 steps
  1. Use the dedicated wall bracket with the projector upside-down; ask the dealer for details.
  2. Keep as far as possible and at least 1 m from fire detectors/alarms to avoid false activation from hot exhaust.
  3. Avoid strong lights/fluorescent lamps near the receiver and test remote operation at the proposed position before mounting.
  4. Set upside-down projection with Screen Settings > Ceiling Projection On; Off is for table top.
  5. No mounting screw dimensions or vertical projection permission is inferred.

Monitor out端子の利用について

Instructions from the manual
Use MONITOR OUT4 steps
  1. While on, Computer 1 sends COMPUTER IN 1 through MONITOR OUT; Computer 2 sends COMPUTER IN 2.
  2. For Video, S-Video, HDMI 1/2 it continues the later-selected Computer 1 or Computer 2 input, e.g.
  3. Computer 1→S-Video keeps the IN 1 signal.
  4. Standby can output only COMPUTER IN 1 when Standby RGB/Audio is enabled; IN 2 cannot output in standby.

投映距離と投映サイズについて

Instructions from the manual
Projection-distance and geometry reference3 steps
  1. Approximate WXGA installation guides: screen inches/diagonal cm/Lcm/hcm: 50/127/6/24; 60/152/13/27; 80/203/27/32; 100/254/40/38; 110/279/47/40.
  2. L is measured from the product front to the projection surface; h from product bottom to picture bottom.
  3. Use only the WXGA branch for XJ-UT351W.
Projection geometry for the XJ-UT351W WXGA branch. The complete distance table remains in the instructions.
Projection geometry for the XJ-UT351W WXGA branch. The complete distance table remains in the instructions.

Diagram key

  • h: Height from the product bottom to the picture bottom, shown by the complete vertical two-ended arrow.
  • L: Distance from the product front to the projection surface, shown by the complete horizontal two-ended arrow. Approximate screen inches/L cm/h cm: 50/6/24; 60/13/27; 80/27/32; 100/40/38; 110/47/40.

プロジェクターのrs-232c制御について

Instructions from the manual
RS-232C connection and protocol10 steps
  1. Connect computer and SERIAL with a commercial cross serial cable.
  2. Use 19200 bps, 8 data bits, no parity, 1 stop bit, no flow control.
  3. Commands use ASCII and decimal integers.
  4. Read format (COMMAND?) returns (setting-range, current-value); write (COMMAND value).
  5. Example (VOL?) returns (0-30, 15); (VOL 0) mutes.
  6. Unrecognized command returns?; unsupported setting values are ignored.
  7. Wait for the previous command or body/remote key operation to complete before sending the next.
  8. While off send only PWR?, LMP? or PWR 1.
  9. BLK and ARZ require a valid input signal.
  10. Only model-supported commands/values apply.

コマンド一覧

Instructions from the manual
RS-232C picture and audio command values14 steps
  1. PWR 0/1 Off/On.
  2. SRC 0 RGB 1, 1 Component 1, 2 Video, 3 RGB 2, 4 Component 2, 6 Auto 1, 7 HDMI 1, 9 S-Video, 10 Auto 2, 14 HDMI 2; network/media/calculator values do not apply.
  3. AIS 1 AUDIO IN 1, 2 AUDIO IN 2, 3 AUDIO IN R/L, 4 HDMI 1 audio, 5 HDMI 2 audio.
  4. BLK 0/1 blank; VOL 0–30 (mute–max); VLP/VLM raise/lower by the amount sent (e.g.
  5. VLP 5/VLM 5); MUT 0/1 mute.
  6. PST 1 Graphics, 2 Theater, 3 Standard, 4 Blackboard, 5 Natural.
  7. ARZ 0 Standard for RGB/HDMI-PC, 2 Standard for Component/HDMI-DTV/Video/S-Video; 1=16:9, 3 Letterbox, 4 Full, 5 Real, 6=4:3, 7=16:10 subject to source-supported choices.
  8. LMP reads cumulative light hours.
  9. PMD 0 Bright, 1 Normal (only Light Control Off); 2 brightness sensor On; 3–9 Light Output 7, 6, 5, 4, 3, 2, 1.
  10. FRZ 0/1 Freeze.
  11. KST 0–120 is vertical keystone (GUI−60..60); KSP/KSM increment/decrement by amount.
  12. HKS 0–120 horizontal keystone (GUI−60..60); HKP/HKM increment/decrement by amount.
  13. MIC 0–3 microphone level.
  14. Audio adjustment applies to the current source.
RS-232C key, status and installation commands6 steps
  1. KEY values correspond to the remote key operations and must follow the same operation order: 1 Up, 2 Down, 3 Left, 4 Right, 5 ENTER, 6 ESC, 10 FUNC, 11 MENU, 12 POWER, 13 AUTO, 14 INPUT, 15 TIMER, 16 ASPECT, 17 BLANK, 18 FREEZE, 19 printed light-control key, 20 KEYSTONE+, 21 KEYSTONE−, 22 D-ZOOM+, 23 D-ZOOM−, 24 VOLUME+, 25 VOLUME−.
  2. Playback KEY 26–30 belongs to the network branch.
  3. POS 0 top-up/front, 1 top-down/rear, 2 top-up/rear, 3 top-down/front; these implement Projection Method/Ceiling Projection.
  4. APO 0 Off, 1=5 min, 2=10 min, 3=15 min, 4=20 min, 5=30 min.
  5. STS queries error status: 0 normal, 1 fan, 2 temperature, 7 light, 16 other; these are serial query values, not display codes.
  6. IDS 0 All, 1–4 corresponding projector ID.

仕様

Instructions from the manual
Verified specifications and environment7 steps
  1. XJ-UT351W: 1-chip DLP, 0.65-inch WXGA 1280×800, 16:10; fixed zoom/manual focus F 2.3/f 4.2; laser/LED; 50–110 inch images; 3500 lm, 20000:1 under Light Control Off Bright/JISX 6911:2015 conditions, not a guarantee of every unit.
  2. Native 1280×800; maximum compressed RGB/HDMI 1920×1200, component 1920×1080.
  3. Horizontal 15–91 kHz, vertical 50–85 Hz; 16 W mono speaker.
  4. Operate 5–35°C, 20–80 percent humidity without condensation, altitude 0–3000 m with High Altitude On at 1500–3000 m.
  5. Japan 100 V AC 50/60 Hz.
  6. Light Control On output 7=185 W, output 1=105 W; Off Bright 225 W, Off Normal 200 W; standby 0.12 W.
  7. Approx 338 mm width×333 mm depth×153 mm thickness including protrusions, 5.7 kg; dimensions/weight exclude cable cover.

はじめに

Instructions from the manual
Check firmware version and update requirements6 steps
  1. Check the official CASIO support page for firmware for this exact projector and note its version.
  2. While projecting, press MENU, select Information with Up/Down and read Version.
  3. Update is possible only if the published version is newer.
  4. The guide lists Windows 8, Windows 7 SP1, Vista SP2 and XP SP3 (32-bit), on a compatible PC with its preinstalled listed OS, Pentium M 1.6 GHz or higher plus OS-recommended CPU/memory, full-colour display at least 1024 × 768, keyboard and pointing device.
  5. It does not establish support for newer operating systems.
  6. Obtain a suitable USB cable, USB DRIVER for CASIO Projector, CASIO Projector Flash Loader and the exact model’s .cpr firmware from official support.
Related instructions: Connect for firmware or user-logo transfer · Install the firmware USB driver · Update the projector firmware
Prepare user-logo transfer software and image6 steps
  1. The generic guide lists possible startup/blank/no-signal uses; this model’s operation guide confirms blank/no-signal Logo settings.
  2. Obtain USB DRIVER for CASIO Projector, CASIO Projector LOGO Loader, model-specific .cph header and the image from the official support service.
  3. Use a USB cable matching the LOGO MicroUSB TypeB port.
  4. Published environment: Windows 8 / 7 SP1 / Vista SP2/XP SP3 (32-bit), preinstalled IBM PC/AT-compatible computer, Pentium M 1.6 GHz or higher and the OS-recommended CPU, OS-recommended memory, full-colour 1024×768 or higher display, keyboard and pointer.
  5. These are historic guide requirements, not a claim of current support.
  6. Use RGB 24-bit full-colour BMP, 640×480 through 1280×800; 1280×800 matches this model’s native resolution.

Usbドライバーをインストールするには

Instructions from the manual
Install the firmware USB driver6 steps
  1. Install the driver before USB-connecting the projector.
  2. Otherwise the PC cannot recognise it or transfer data.
  3. If connected prematurely, unplug the PC USB cable, install the driver and reconnect.
  4. Download USB DRIVER for CASIO Projector from official support and double-click PjUsbDriverSetup_EN.exe.
  5. Follow its dialogs.
  6. For User Account Control choose Yes on Windows 7/8 or Allow on Vista; on the illustrated XP prompt choose Continue.
Install the user-logo USB driver before connection4 steps
  1. Before USB connection download USB DRIVER for CASIO Projector.
  2. Run PjUsbDriverSetup_EN.exe and follow dialogs.
  3. Windows 7/8: choose Yes at UAC; Vista: Allow; XP: Continue at its warning.
  4. If USB was connected first, unplug USB, install the driver, then reconnect; without the driver transfer cannot work.

プロジェクターのファームウェアを更新するには

Instructions from the manual
Update the projector firmware14 steps
  1. On the update PC, download the Flash Loader and exact-model firmware ZIPs from official support.
  2. Extract both into the same folder.
  3. Unplug the projector power cord from the outlet.
  4. Connect the computer USB port to the projector’s firmware/ROM-update USB port with a suitable cable; for XJ-UT351W this is the Micro-USB LOGO terminal documented in the operation guide.
  5. Connect the projector power cord to the outlet and turn on.
  6. POWER flashes orange in the guide’s one-second-on/one-second-off pattern.
  7. Close all running PC applications.
  8. Double-click PjFlashLoader_EN.exe.
  9. Click Choose, select the exact .cpr firmware in the Open dialog, then Open.
  10. Click Upload.
  11. During transfer the projector POWER indicator goes out and the PC progress bar shows progress; on completion a dialog appears and POWER flashes orange.
  12. Never turn off the projector or PC, or disconnect USB, during data transfer.
  13. After completion click OK, then the window’s upper-right X to close the Flash Loader.
  14. Remove the USB cable from both projector and PC, then unplug the projector power cord from the outlet.
Related instructions: Connect for firmware or user-logo transfer · Check firmware version and update requirements · Install the firmware USB driver

プロジェクターにユーザーロゴを転送するには

Instructions from the manual
Transfer the user-logo image18 steps
  1. Transfer erases the previously stored logo.
  2. Download LOGO Loader and exact-model header ZIP files; extract both to the same computer folder.
  3. Put the chosen BMP there.
  4. Unplug projector mains if connected.
  5. Connect computer USB to the LOGO firmware/ROM-update port.
  6. Plug mains in and power on; POWER flashes orange 1 second on / 1 second off.
  7. Close all computer applications.
  8. Run PjLogoLoader_EN.exe.
  9. Click upper Choose, select exact-model .cph and Open.
  10. Check LOGO Header File Format: OK.
  11. If absent, obtain an uncorrupted exact-model header and repeat from upper Choose.
  12. Click lower Choose, select image and Open.
  13. Check Image File Format: OK.
  14. If absent use a BMP meeting the complete requirements and repeat from lower Choose.
  15. Click Upload.
  16. During transfer POWER goes off and progress appears; completion shows a dialog and POWER resumes orange flashing.
  17. Never interrupt either power supply or unplug USB during transfer.
  18. Click OK, close LOGO Loader with its top-right close control, remove USB from both devices, then unplug projector mains.
Related instructions: Connect for firmware or user-logo transfer · Check firmware version and update requirements · Install the firmware USB driver

Xj-ut331x/xj-ut311wn/xj-ut351w/xj-ut351wn

Instructions from the manual
Supported source timings6 steps
  1. RGB (VESA): 640×480 at 60/72/75/85 Hz; 800×600 at 56/60/72/75/85 Hz; 1024×768 at 60/70/75/85 Hz; 1152×864/75; 1280×720/60; 1280×768/60; 1280×800/60; 1280×960/60; 1280×1024 at 60/75/85; 1366×768/60; 1400×1050/60; 1440×900/60; 1600×1200/60; 1680×1050/60; 1920×1080/60; 1920×1200 RB/60.
  2. Component HDTV: 1080 p 50/60,720 p 50/60, 1080 i 50/60.
  3. Component SDTV: 576 p 50,576 i 50,480 p 60,480 i 60.
  4. HDMI: 640×480/60,800×600/60, 1024×768/60, 1280×720/60, 1280×768/60, 1280×800/60, 1280×960/60, 1280×1024/60, 1400×1050/60, 1920×1080/60, 1920×1200 RB/60; SDTV 480 p, 576 p; HDTV 720 p 50/60, 1080 i 50/60, 1080 p 50/60.
  5. Video: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL 60, SECAM.
  6. Native XJ-UT351W projection remains 1280×800.

Model details

Model and compatibility

Native resolution
WXGA 1280 × 800, 16:10, 0.65-inch DLP; fixed zoom, manual focus.
Power supply
100 V AC, 50/60 Hz; Japan only.
Operating environment
5–35°C, 20–80% humidity without condensation; altitude 0–3000 m.
Size and mass
338 × 333 × 153 mm (W × D × H), including protrusions; approximately 5.7 kg. Both exclude the cable cover.

Manuals and sources

  1. CASIO operation manual
  2. CASIO model support and details
  3. CASIO manual download listing
  4. CASIO operation manual
  5. CASIO operation manual
  6. CASIO operation manual
ManualGrid

Manuals, error messages and practical checks for the products you own.

An independent reference. Product names and trademarks belong to their respective owners.