The checks and guides below come from the official manuals for this model.
No matches for this wording. Try a light name, error code or a shorter phrase.
Troubleshooting
Find the problem you are experiencing
Unable to power on.2 checks
Battery low. Put the robot on the charging dock and charge it before use.
Battery low. Put the robot on the charging dock and charge it before use.
Battery temperature too low or too high. Only use the robot within the range of 4-40°C (39-104°F).
Battery temperature too low or too high. Only use the robot within the range of 4-40°C (39-104°F).
Unable to charge.3 checks
Dock not connected to power. Check whether both ends of the power cord are properly connected.
Dock not connected to power. Check whether both ends of the power cord are properly connected.
Poor contact. Clean the charging contacts of the dock and the robot.
Poor contact. Clean the charging contacts of the dock and the robot.
Confirm that the dock indicator light is on.
Confirm that the dock indicator light is on.
Slow charging.2 checks
When used at high or low temperatures, the robot will automatically reduce its charging speed to extend battery life.
When used at high or low temperatures, the robot will automatically reduce its charging speed to extend battery life.
Charging contacts dirty. Wipe them with a dry cloth.
Charging contacts dirty. Wipe them with a dry cloth.
Unable to dock.3 checks
Too many obstacles near the dock. Move it to an open area.
Too many obstacles near the dock. Move it to an open area.
The robot is too far from the charging dock. Place it closer and retry.
The robot is too far from the charging dock. Place it closer and retry.
The dock locator may be dirty. Wipe it with a dry cloth.
The dock locator may be dirty. Wipe it with a dry cloth.
Noise during cleaning.2 checks
The main brush, side brush, or main wheels may be jammed. Turn off the robot and clean them.
The main brush, side brush, or main wheels may be jammed. Turn off the robot and clean them.
The omnidirectional wheel may be jammed. Use a screwdriver to remove it for cleaning.
The omnidirectional wheel may be jammed. Use a screwdriver to remove it for cleaning.
Unable to connect to WiFi.4 checks
WiFi disabled. Reset the WiFi and try again.
WiFi disabled. Reset the WiFi and try again.
Poor WiFi signal. Move the robot to an area with good WiFi reception.
Poor WiFi signal. Move the robot to an area with good WiFi reception.
Abnormal WiFi connection. Reset the WiFi, download the latest mobile app and retry.
Abnormal WiFi connection. Reset the WiFi, download the latest mobile app and retry.
Unable to connect to WiFi abruptly. There may be an error with your router settings. Contact Roborock Customer Service for help with troubleshooting.
Unable to connect to WiFi abruptly. There may be an error with your router settings. Contact Roborock Customer Service for help with troubleshooting.
Is power always being drawn when the robot is on the charging dock?1 check
The robot will draw power while it is docked to maintain battery performance, but the power consumption is extremely low.
The robot will draw power while it is docked to maintain battery performance, but the power consumption is extremely low.
Does the robot need to be charged for at least 16 hours for the first three uses?1 check
No. Lithium-ion batteries have no memory effect. The robot can be used once fully charged.
No. Lithium-ion batteries have no memory effect. The robot can be used once fully charged.
Cleaning does not resume after recharging.2 checks
Make sure that the robot is not in DND mode. DND mode will prevent cleanup.
Make sure that the robot is not in DND mode. DND mode will prevent cleanup.
The robot will not resume cleaning if users press button to recharge or manually place the robot back to the dock.
The robot will not resume cleaning if users press Dock to recharge or manually place the robot back to the dock.
The robot suddenly misses a certain spot.1 check
The wall sensor, cliff sensors, or carpet sensor may be dirty. Wipe them with a soft dry cloth.
The wall sensor, cliff sensors, or carpet sensor may be dirty. Wipe them with a soft dry cloth.
Schedules are not effective.1 check
Schedules will only take effect when the battery is higher than 15%.
Schedules will only take effect when the battery is higher than 15%.
The LED status indicator light on the dock is steady red.4 checks
Voltage error. Check that the local voltage meets the requirements listed on the dock.
Voltage error. Check that the local voltage meets the requirements listed on the dock.
Check clean water tank placement or refill as required.
Check clean water tank placement or refill as required.
Check dirty water tank placement or empty as required.
Check dirty water tank placement or empty as required.
Check that the cleaning tank or cleaning tank filter has been correctly installed.
Check that the cleaning tank or cleaning tank filter has been correctly installed.
Reduced emptying performance or unusual noise when emptying.2 checks
The main brush or main brush cover is not properly installed. Check and install in place.
The main brush or main brush cover is not properly installed. Check and install in place.
The filter, air duct, suction inlet, air inlet, dustbin or dust bag is blocked. Clean to remove blockages.
The filter, air duct, suction inlet, air inlet, dustbin or dust bag is blocked. Clean to remove blockages.
Reduced mop washing performance.2 checks
The mop cloths are not attached properly. Reinstall.
The mop cloths are not attached properly. Reinstall.
The floor is dirty. Change the mop washing mode in the app for better cleaning.
The floor is dirty. Change the mop washing mode in the app for better cleaning.
Unable to start auto-drying.2 checks
Auto-drying is disabled. Check in-app settings.
Auto-drying is disabled. Check in-app settings.
Auto-drying starts only after mopping or mop washing.
Auto-drying starts only after mopping or mop washing.
Unable to auto-empty.4 checks
Auto-emptying is disabled. Check in-app settings.
Auto-emptying is disabled. Check in-app settings.
Dock dust container cover is not installed. Check and install.
Dock dust container cover is not installed. Check and install.
Auto-emptying will not be triggered if the robot returns to the dock without cleaning.
Auto-emptying will not be triggered if the robot returns to the dock without cleaning.
The robot will not auto-emptying after returning to the dock in the Do Not Disturb (DND) mode. Adjust cleaning or DND duration, or start emptying manually.
The robot will not auto-emptying after returning to the dock in the Do Not Disturb (DND) mode. Adjust cleaning or DND duration, or start emptying manually.
Unable to wash the mop cloths.5 checks
The mop will not be washed if not used.
The mop will not be washed if not used.
If the robot does not start from the dock or no dock is found on the app map, it will not return to the dock for mop washing.
If the robot does not start from the dock or no dock is found on the app map, it will not return to the dock for mop washing.
Check clean water tank placement or refill as required.
Check clean water tank placement or refill as required.
Check dirty water tank placement or empty as required.
Check dirty water tank placement or empty as required.
Check that the cleaning tank or cleaning tank filter has been correctly installed.
Check that the cleaning tank or cleaning tank filter has been correctly installed.
Guides
Safety information
Instructions from the manual
Safety restrictions26 steps
WARNING: For the purposes of recharging the battery, only use the detachable docking station roborock EWFD24HRR provided with this product.
WARNING: The product must be switched off and the plug must be removed from socket outlet before cleaning or maintaining the product.
WARNING: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
CAUTION: Do not use this product on elevated surfaces without barriers such as the floor of a loft, an open-ended terrace, a slide, or top of furniture.
CAUTION: To prevent blocking the product and to avoid damage to valuables, remove lightweight items (such as plastic bags) and fragile objects (such as vases) from the floor before cleaning.
CAUTION: Do not use the product to clean hard or sharp objects (such as decoration wastes, glass, and nails) to avoid scratching the robot or the floor.
CAUTION: Before placing the robot into storage, charge it fully, turn it off, and then choose a cool, dry place.
Recharge it at least every three months to avoid battery overdischarge.
CAUTION: Do not place any object near the suction inlet of the dock.
CAUTION: Do not put fingers into the seam of the dock to avoid possible injury.
CAUTION: Do not operate the product in a room where an infant or child is sleeping.
CAUTION: Do not carry the robot using vertical bumper, top cover, side brush or bumper.
Do not move the dock by lifting the dock base, water tank handles or dust container cover.
CAUTION: Make sure the robot is compatible with the dock, otherwise emptying or charging may fail.
CAUTION: Do not use the dock to pick up stones, paper scraps, or other objects that may block the air duct.
If the air duct gets blocked, clean it immediately.
CAUTION: Place the dock on a hard, flat floor away from fire, heat, and water.
Avoid narrow spaces or locations where the robot may be suspended in the air.
CAUTION: Do not place any object, child, or pet on the product or dock, or cover it with any item (including dust-proof cover) whether it is in operation or not.
CAUTION: Do not pick up anything burning or smoking, such as cigarettes, matches, or hot ashes.
CAUTION: Do not use the dock to pick up flammable or explosive objects such as fire lighter, gasoline, and toner used in printers or copiers.
CAUTION: Do not rinse the robot and the dock.
CAUTION: Only use the product in accordance with the User Manual.
Any loss or damage caused by improper use will be borne by the user.
CAUTION: Make sure dustbin, washable filter, dust bag, side brush, mop cloths, main brush and main brush cover are installed in place before cleaning.
CAUTION: Do not sit or stand on the robot or dock.
Water, battery, charging and transport precautions13 steps
Be sure that the supply voltage meets the requirements listed on the dock.
Only use the power cord provided with the product to prevent potential smoke, heat, or fire.
Do not use the product with any type of power adapter, as this may cause danger and void the warranty.
If the dock is placed in an area susceptible to thunderstorms or with unstable voltage, take protection measures.
Unplug the power cord before placing the dock into storage.
Do not discard waste batteries.
Leave them with a professional recycling organization.
To transport the product, make sure it is powered off and shut down, and empty the remaining fluid in the water tanks.
Original packaging is advised.
Battery and Charging WARNING To prevent corrosion or damage, do not use any disinfectant and only use cleaning solution recommended by Roborock in the water tank.
Do not put any low objects (such as shoes, mats) near raised areas like stairs.
Otherwise, the robot may fall down caused by malfunctional sensors.
To prevent water damage, make sure that the floor where the robot operates is free of water.
Product overview
Instructions from the manual
Robot controls and indicator lights5 steps
Hold Power/Clean to turn the robot on or off; press to start cleaning.
Press Dock to return to the dock or start emptying; hold Dock to start spot cleaning or mop washing.
Any button stops the robot during cleaning or docking.
Power light: white at battery level 15% or higher; red below 15%; breathing while charging or starting; flashing red on error.
WiFi light: off when WiFi is disabled or charging; slowly flashing while waiting for connection; quickly flashing while connecting; steady when connected.
Dock indicator lights2 steps
Breathing means emptying or mop washing; red means dock error; off means powered off or charging.
The status light is on when the dock is powered on and goes off while the robot charges.
Identify robot, dustbin, mop and dock parts3 steps
Use the complete reviewed overview diagrams and keys to identify all sensors, wheels, brushes, latches, tanks, filters, refill and suction ports.
Secure mop cloths in place on their mounts.
The manual names QX1PEC robot and EWFD24HRR dock.
Installation
Instructions from the manual
Prepare the cleaning area4 steps
Tidy cords, hard or sharp objects such as nails and glass, and loose items.
Move unstable, fragile, precious or dangerous objects to prevent personal injury or property damage from tangling, collisions or items being knocked over.
In raised areas, always use a secure physical barrier to prevent accidental falls and injury or damage.
During first use, follow the whole cleaning route and watch for potential problems; the robot can clean by itself on later uses.
Assemble the dock and mop modules6 steps
Place the dock on a hard, flat floor.
Attach its base by pressing both sides down firmly and then pressing the middle connection until it clicks.
Secure water tanks when moving the dock so they do not fall off.
Connect the power cord at the back and store excess cord in the storage slot.
The cord can exit either side.
Align and install the mop axles until they click.
Position the dock11 steps
Keep clearance of about 0.9 m (2.9 ft) in height, 0.4 m (1.3 ft) in length and 1.2 m (3.9 ft) in width, as the source describes and its diagram labels.
Place on a hard, flat wood, tile or concrete floor against a wall with good WiFi.
Plug in and check the dock status light is on.
Do not let the cord hang vertically where the robot can catch it and move or disconnect the dock.
The status light goes off while charging and turns red on error.
Avoid fire, heat, water, narrow spaces and suspended positions.
Soft carpet or mats can tilt the dock and impede docking or departure.
Avoid direct sunlight and anything blocking the dock location beacon.
Never use the dock without the clean and dirty water tanks, dust container cover, disposable dust bag or cleaning tank.
Follow maintenance instructions; do not clean the dock with a wet cloth or tissue.
A small amount of water in the waterway is normal after factory testing.
Power on and charge6 steps
Hold Power/Clean to turn on.
Wait for a steady power light, then place the robot on the powered dock.
Press Dock to return automatically for charging.
The dock light turns off and the robot power light breathes during charging.
Keep the built-in lithium-ion battery charged for performance.
If low battery prevents startup, place the robot on the dock to charge.
Connecting to the app
Instructions from the manual
Connect the app and reset WiFi8 steps
Search for Roborock in the App Store or Google Play, or use the official manual QR code, to install the app.
Open the top cover and find the WiFi light.
Hold Power/Clean and Dock together until the Resetting WiFi voice message.
Slowly flashing WiFi means reset is complete and the robot waits for connection.
If router configuration, a forgotten password or any other issue prevents connection, reset WiFi and add as a new device.
Open Roborock, tap Scan to Connect or Search for Device, and follow the app instructions.
Updates may change the process.
Only 2.4 GHz WiFi is supported.
Instructions for use
Instructions from the manual
Turn on and offView
Hold Power/Clean to turn on; its light comes on and the robot waits. Hold it to turn off and end the cleaning cycle. The robot cannot turn off while charging.
Fill the clean water tank6 steps
Remove and open the clean water tank.
Fill with water to MAX, close the lid, lock the latch and refit.
Use no disinfectant and only Roborock-recommended cleaning solution to avoid corrosion or damage.
Too much solution can cause slipping and improper operation.
Use no hot water, which can deform the tank.
Wipe remaining water marks before refitting.
Start cleaning9 steps
Press Power/Clean to start.
The robot scans the room, divides it into zones, cleans zone edges and then fills each in a zigzag pattern.
Start from the dock for automatic vacuuming and return; do not move the dock during cleaning.
Charge if battery is too low to start.
Tidy cords, including the dock cord, and valuables to prevent dragging, disconnection and damage.
If cleaning finishes in under 10 minutes, the area is cleaned twice.
If battery runs low, the robot returns to charge and then resumes where it stopped.
It retracts mop mounts on carpet; carpet can also be set as a no-go zone.
Ensure mop cloths are properly installed before every task.
Spot cleaningView
While paused, hold Dock to spot clean a 1.5 m (4.9 ft) square centered on the robot. Afterward it returns to the starting point and waits.
Pause and resumeView
While running, press any button to pause. Press Power/Clean to resume or Dock to return. Manually docking a paused robot ends the current cleanup.
Sleep and wake3 steps
After more than 10 minutes paused, the robot sleeps and the power light flashes every few seconds.
Any button wakes it.
It does not sleep while charging and automatically shuts down after more than 12 hours asleep.
Do Not Disturb mode3 steps
The default period is 22:00–08:00.
Disable or change DND in the app.
During DND the robot does not automatically resume cleaning, the power light dims and voice-message volume decreases.
Wash mop cloths6 steps
During cleaning the robot decides when to return for mop washing and tank refill.
Tap Dock in the app to send it for washing during cleaning.
While charging, hold Dock on the robot or tap Wash in the app to start washing manually.
Any button stops washing.
Start from the dock and leave the dock in place for automatic washing.
Change wash frequency and mode in the app.
Empty the dustbin automatically or manually5 steps
Automatic emptying starts after cleaning when the robot returns to dock.
Press Dock on the docked robot or the corresponding app button to empty manually; any button stops it.
After prolonged nonuse of auto-emptying, empty the dustbin manually and clear the air inlet for performance.
Auto-emptying can be disabled in the app.
Avoid frequent manual emptying.
Dry mop cloths3 steps
Drying begins automatically after mop washing or completed cleaning.
Start or stop manually with the corresponding app button.
Change duration or disable automatic drying in the app.
Return and charge3 steps
After cleaning the robot returns to charge.
While paused press Dock; the power light breathes while charging.
If the dock cannot be found, the robot returns to its starting place; dock it manually to recharge.
Error notifications4 steps
On error the robot power light flashes red or dock status light stays red.
The app receives a popup and a voice alert may sound.
After more than 10 minutes malfunctioning the robot sleeps.
Manually docking a malfunctioning robot ends the cleanup.
Reset the systemView
If buttons do not respond or the robot cannot turn off, press Reset to reset the system. Scheduled cleaning, WiFi and other existing settings return to factory settings.
Deactivate WiFiView
Hold Reset until a voice message sounds. Wait 5 minutes for automatic WiFi deactivation. To reconnect, follow the app connection instructions.
Restore factory settings2 steps
If a system reset does not restore proper function, switch on the robot.
Hold Dock and press Reset at the same time until the Restoring factory settings voice message; factory settings are restored.
Routine maintenance
Instructions from the manual
Clean the main brush9 steps
Switch off and unplug before cleaning or maintenance.
Clean every 2 weeks and replace every 6–12 months; replace immediately on abnormal wear.
Turn the robot over and press main-brush latches to remove the cover.
Pull out the brush and remove its bearing.
Rotate caps in the indicated unlock direction, remove them and clear hair or dirt at both ends.
Reinstall the main brush.
Refit the cover with all four teeth fully seated in the slot, then press until it locks with a click.
Wipe the brush with a wet cloth; air-dry out of direct sunlight if wet.
Use no corrosive cleaning fluid or disinfectant.
Clean the side brush3 steps
Switch off and unplug first.
Clean monthly and replace every 3–6 months, or immediately on abnormal wear.
Unscrew the side-brush screw, remove and clean the brush, reinstall and tighten.
Clean the omnidirectional wheel6 steps
Switch off and unplug first.
Clean as required.
Pry out the axle with a tool such as a small screwdriver and remove the wheel.
Its bracket cannot be removed.
Rinse wheel and axle with water to remove hair and dirt.
Dry, reattach and press the wheel firmly into place.
Clean the main wheelView
Switch off and unplug first. Clean as required with a soft, dry cloth.
Clean the dustbin8 steps
Switch off and unplug first.
Clean as required.
Open the top cover, press the dustbin latch and remove the dustbin.
Open the washable filter and empty the bin.
Fill the bin with clean water and reinstall the washable filter.
Shake gently and pour out dirty water.
Use only clean water without cleaning liquid to prevent blockage.
Leave dustbin and washable filter to dry.
Clean the washable filter5 steps
Switch off and unplug first.
Clean every 2 weeks and replace every 6–12 months, or immediately on abnormal wear.
Remove the filter, rinse repeatedly and tap to remove as much dirt as possible.
Do not touch the filter surface with hands, brush or hard objects, which can damage it.
Allow at least 24 hours to dry thoroughly before reinstalling.
Clean and refit mop cloths5 steps
Switch off and unplug first.
Clean as required and replace every 1–3 months, or immediately on abnormal wear.
Remove each cloth from its mount, clean and air-dry.
Stick cloths firmly in position on their mounts.
A dirty mop impairs washing performance; clean it before use.
Clean robot sensors2 steps
Switch off and unplug first.
Clean as required with a soft, dry cloth: dock locator, Reactive Tech obstacle avoidance sensor, wall sensor, communication sensor, carpet sensor and all four cliff sensors.
Move the dockView
Lift and move the dock. Never lift by its base, tank handles or dust container cover directly, to prevent the dock falling off. Secure tanks before moving so they cannot fall off.
Clean the dirty water tank5 steps
Switch off and unplug first.
Clean as required.
Open its lid and pour out dirty water.
Fill with clean water, close and shake.
Pour out the dirty water, close the lid and reinstall.
Clean charging contactsView
Switch off and unplug first. Clean monthly using a soft, dry cloth on robot and dock contacts.
Replace the disposable dust bag8 steps
Switch off and unplug first.
Replace as required.
Remove the dust container cover, remove the bag in the arrow direction and discard it; the handle seals the bag on removal to prevent leakage.
Always fit a bag before closing the cover to prevent emptying without a bag; auto-emptying can also be disabled in the app.
Clean around the filter with a dry cloth.
Fit a new bag along the slot and unfold for best emptying performance.
Close the cover securely.
Ensure the bag is properly sealed to prevent escaping waste and dock damage.
Clean the cleaning tankView
Switch off and unplug first. Clean as required. Remove the cleaning tank, rinse it and its filter with water, and reinstall.
A
Instructions from the manual
Robot and dock overview diagramsView
Use the reviewed diagrams with the complete keys and corresponding instructions. Follow the source conditions, quantities and warnings.
B
Instructions from the manual
Dock installation and brush care diagramsView
Use the reviewed diagrams with the complete keys and corresponding instructions. Follow the source conditions, quantities and warnings.
Dock assembly, cord routing, mop fitting, clearances and charging. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
B2: Assembly.
B2-1: Hard, flat floor; press both base sides and middle connection until it clicks.
B2-2: Click at the first base connection.
B2-2 repeated: Click at the second base connection.
B2-3: Connect cord at back and store excess; cord can exit either side.
B2-4: Align and fit mop axles.
B2-5: Click when mop axles are seated.
B3: Place against wall on hard flat floor with good WiFi; retain all placement warnings.
B3-1: About 0.9 m (2.9 ft) overhead clearance.
B3-2: About 0.4 m (1.3 ft) clearance as marked.
B3-3: About 1.2 m (3.9 ft) clearance as marked.
B4: Hold Power/Clean, wait for steady light and place on powered dock; Dock returns robot for charge.
B4-1: Dock status light off and robot power light breathing means charging; directly dock if too low to start.
Main brush removal, cap and bearing cleaning, cover refitting and side brush care. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
D: Routine maintenance; switch off and unplug first.
D1: Main brush: clean every 2 weeks; replace every 6–12 months or on abnormal wear.
D1-1: Main-brush cover.
D1-2: Main-brush cover latches, both locations.
D1-3: Main brush.
D1-4: Main-brush caps.
D1-5: Main-brush bearing.
D1-6: Turn over and press latches to remove cover.
D1-7: Remove brush and bearing; rotate caps in unlock direction and remove; clear hair and dirt at both ends.
D1-8: Reinstall main brush.
D1-9: Seat all four cover teeth in slot; press to lock with a click. Wipe brush with wet cloth and air-dry away from sunlight; no corrosive cleaners or disinfectants.
D2: Side brush: clean monthly, replace every 3–6 months or on abnormal wear. Unscrew, remove, clean, reinstall and tighten.
D
Instructions from the manual
Wheel, dustbin, filter and sensor diagramsView
Use the reviewed diagrams with the complete keys and corresponding instructions. Follow the source conditions, quantities and warnings.
Wheel, dustbin, filter and mop-cloth care. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
D: Routine maintenance; switch off and unplug first.
D3: Omnidirectional wheel: clean as required; bracket cannot be removed.
D3-1: Pry axle out using a tool such as a small screwdriver; remove wheel.
D3-2: Rinse wheel and axle, dry and firmly reattach.
D4: Main wheel: clean as required with soft dry cloth.
D5: Dustbin: clean as required.
D5-1: Open top cover and press latch to remove.
D5-2: Open washable filter and empty bin.
D5-3: Fill with clean water and refit filter, shake gently and pour out dirty water; no cleaning liquid.
D5-4: Leave bin and filter to dry.
D6: Washable filter: clean every 2 weeks; replace every 6–12 months or on abnormal wear.
D6-1: Remove filter.
D6-2: Rinse repeatedly and tap out dirt; do not touch surface with hands, brush or hard objects.
D6-3: Dry thoroughly for at least 24 hours before refitting.
24-hour symbol: At least 24 hours drying.
D7: Mop cloths: clean as required; replace every 1–3 months or on abnormal wear.
D7-1: Remove cloth from mount, clean and air-dry.
D7-2: Stick cloth firmly in position; a dirty cloth impairs performance, so clean before use.
Dock and dust bag maintenance diagramsView
Use the reviewed diagrams with the complete keys and corresponding instructions. Follow the source conditions, quantities and warnings.
Dirty water tank and charging-contact care. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
D: Routine maintenance; switch off and unplug first.
D10: Dirty water tank: clean as required. Open lid, empty, fill with clean water, close and shake; empty, close and reinstall.
D11: Charging contacts: clean monthly with soft dry cloth on both robot and dock.
D12: Replace bag as required; switch off and unplug first.
D12-1: Remove dust container cover to begin bag replacement.
Complete disposable dust bag replacement and cleaning-tank rinsing. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
D12-2: Remove and discard bag in arrow direction; handle seals it against leakage. Always fit a bag before closing cover or disable auto-emptying in app.
D12-3: Clean around filter with dry cloth; install new bag along slot and unfold for performance.
D12-4: Close cover securely and ensure bag properly sealed to prevent escaping waste and dock damage.
D13: Cleaning tank: clean as required; switch off and unplug first.
D13-1: Remove cleaning tank.
D13-2: Rinse cleaning tank and filter with water.
D13-3: Reinstall cleaning tank.
Controls and parts
See the manual diagrams 2 diagrams
Power/Clean, Dock and battery indicator instructions. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.Robot top, underside and open-cover parts. Qrevo S CE, 220–240 V EWFD24HRR dock; FCC 120 V excluded.
Diagram key
A: Product overview.
A1: Robot top view and control inset.
Power/Clean symbol: Hold on/off; press to clean.
Dock symbol: Press to return or empty; hold for spot cleaning or mop washing.
A1-1: Dock locator.
A1-2: Reactive Tech obstacle avoidance sensor.
A2: Robot underside.
A2-1: Wall sensor.
A2-2: Omnidirectional wheel.
A2-3: Carpet sensor.
A2-4: Side brush.
A2-5: Main wheels, both marked positions.
A2-6: Main brush.
A2-7: Main-brush cover latches, both marked positions.
